Jump to content
Why become a member? ×

Phil_T

Member
  • Posts

    125
  • Joined

  • Last visited

Personal Information

  • Location
    Wakefield

Recent Profile Visitors

The recent visitors block is disabled and is not being shown to other users.

Phil_T's Achievements

Community Regular

Community Regular (8/14)

  • Great Content Rare

Recent Badges

106

Total Watts

  1. the case is 425mm deep excluding the lids and the rail centre to centre is 470mm
  2. Gator 2U rack case in very good condition. A few minor scuffs but pretty much as new. No keys currently but I must have put them somewhere so they might turn up. Collection from Wakefield but could post at cost.
  3. Ian bought my CTM 30 and was a nice chap to deal with.
  4. Phil_T

    Paul C's goodness

    Sold my Jazz bass to bass - very easy transaction. Cheers Paul.
  5. Squier Jazz Bass. 1990/91 Made in Japan. Aged white body with a rosewood board and tort guard. Pickups have been replaced with Toneriders and it's a nice, punchy sounding bass. I had it setup by BJ in Leeds when I bought it and the action is more or less to fender spec, maybe a touch lower. Overall condition is good but there is some damage to the lower edge of the body and a couple of small nicks in the back of the neck up near the 12 fret (so you'll be going to nowhere near them, obviously)
  6. Ashdown CTM-30 all valve amplifier for sale. Lovely condition, one small knick in the tolex along the front edge is the only blemish I can find. These are great amps for a beautiful valve tone at sensible volumes. Collection only from Wakefield, West Yorkshire
  7. USA made SVT 3 pro amplifier for sale. Decent condition for age, front face is clean, top has a few scratches. Left Rack handle has received a knock at some point and is slightly bent. I've not used it for a few years but it's working fine and I did adjust the trim pot when I first got it to make sure it was delivering full power. Open to offers. Collection from Wakefield, West Yorkshire but might be open to shipping if I can't find a local buyer. A 2U gator case is also available that is like new.
  8. I've always loved this bass line but never seen a decent transcription of it so I've had a go at it myself. The bass was split from the mix using Lalal.ai and it did a pretty good job so it's quite easy to hear. I've very little experience at transcribing by ear so I will be off in places no doubt and I've even less experience of writing sheet music so my efforts are probably quite terrible. For a start, it should be in a key which would omit the need for many of the accidentals. If anyone wants to chip in with note correction or sorting out the formatting of the score then please feel free. The guitar pro files are attached together with the stems. The transcription covers the intro and first main section of bass. I haven't done the second section yet but it's pretty much just a mash-up of the first one. There are a few more little variations here and there that I need to work on but, to my ears at least, it's not far off. Let me know what you think. 07 - Primal Scream - Loaded bass split by lalalai.m4a 07 - Primal Scream - Loaded no bass split by lalalai.m4a Loaded - Primal Scream.gp Loaded - Primal Scream.pdf
  9. Would running an 8ohm cab off a 4ohm tap at low volumes be a problem? I've seen plenty of discussions on this topic and the general consensus is that it's not advisable at gig volumes but I've never been clear on whether the volume is a factor. I have an SVT style amp that I picked up cheap which only has 2 or 4ohmn outputs but I only have single 8ohm cab at home for practice and I've never been sure if I run the risk if damaging the amp. The amp is a Bugera so it's possibly not the most robust thing even under perfect operating conditions.
  10. Yes, certainly NW Guitars is basically the same stuff. I went with the Manchester guy because he was the only one who had the surf green and the light tint lacquer. I think NWG only do an amber tint which would have been too strong for my purposes. If you're thinking of giving it go, my advice based on very limited experience would be to get two cans of both colour and clear for a bass body and puts on lots of clear coats - it is very easy to sand through the clear even if you're careful, particularly on edges. You can just about get way with one can of colour if you're only doing a body but if you c@ck something up and need to respray an area you'll soon run out.
  11. Yes, the base colour is pretty much what shows through on the worn patch above the bridge pickup. Everywhere else is mellowed down with a fairly thin coat of the tinted lacquer which is then sealed with clear lacquer so you don't sand through the tinted stuff when you're flatting it. The grubby look comes from using slightly more tint around the bridge area and also - and I kid you not - slathering the whole thing is black liquid shoe polish which then gets wiped off but it seeps into the hairline cracks in the lacquer. The lacquer checking is done by heating up a bit of the body at a time with a hair dryer and then spaying it with pipe freeze. You don't have much control and it tends to create very fine crazing but it looks quite effective It's an enjoyable process and I'm spraying in my garden to avoid being poisoned (nitro is nasty stuff) so it's difficult to perfect paint and this relic process just takes all the stress out of it - you know that if you get a blemish during spraying you can easily disguise it when you come to do the relic treatment.
  12. Thanks - I did it myself using rattle cans from Manchester Guitar Tech. I'm no expert painter but it's fairly easy and obviously the relic finish hides any less than perfect paint. I was inspired by following this thread a while back:
  13. the pickup covers arrived, so one more shot for completeness:
×
×
  • Create New...