Andyjr1515

But I did, of course, play it before I passed it over, although not through a proper bass rig. Very promising indeed and quite different to any other I've used. But I better not spill the beans and spoil Matt's glory

The bass is back with Matt Marriott. I've got one of his 6 string electrics I'm doing some mods on - I'll use it as collateral to make sure he doesn't get too distracted on other things

With the neck timbers having arrived, they have now been joined up which means that most of the major structural components are ready for their respective further stages of work: There are a myriad of small jobs on each, plus a few big and scary ones! The first falls into the small jobs category - fitting the cutaway sides. One is gluing: While the other one is glued and the excess removed. At some stage, the bottom edge will be routed for some maple binding to be fitted. Now that will be scary...

I'm afraid some unavoidable family stuff has got in the way and I won't be able to get there. But I will be at the next one! Have a great one, folks. Andy

Yes - perfectly normal and yes, it's just the geometry. Generally, with a shallow radius and taper, it isn't enough to notice. You could even it out, by tapering the blank, but in my book that's in the 'too hard' territory and for dubious benefit! Looking good, btw

Yup - looking very good. Nice clean routing there, too!

Splendid job!

Good call. Should be fine

And so I'll be moving into a 'planning before doing' phase over the next couple of weeks - not least because there are some grandparenting duties looming which means 'moving all your mess out of the way' But there's a lot to get right and it is worth the pondering without the temptation of cutting or gluing something before I'm sure! This is where I'm at with the wings: The ebony is around 6mm thick and will have a subtle top carve, following the same sort of curve as the back, a couple of diamond 'f' holes and some weight relief scoops in the underneath. And some very careful routing for the switches. Switches? Yes - we're going Jaguar guitar switch system, back mounted. "And so I'll be moving into a 'planning before doing' phase over the next couple of weeks"

And some more wood has arrived. First I added some kerfed linings to stiffen things up: And then repeated everything described above to make the second back: And so, although there are many tasks to be done before I glue them, it was time to rough-cut the tops. I chalked the optimum (only) position for the tops using my modified mould as a guide: This was the longest/widest piece of ebony I could find - not much leeway in any direction! Now you can probably see why I need a visible through-neck And cut, oversize, sitting on the backs: Clearly, there will be the weight of the through neck length to add, but, with some overage and carvings still to take off, all 4 components - 2 tops and 2 backs - are sitting at 3 1/2lbs total. Not bad. A 'standard' solid body blank often gets up to 5lbs, so probably comparable even though it's a much larger body than standard

Bit more progress. First, I made a mod to my thickness callipers. They had flat pads and that made it pretty much impossible to check the thickness across the area of the back or sides because the slightest angle would open up the jaws and give a false reading. I had a rummage in my 'general bits' box and found these caps from some old mirror fixing screws: Out with the dremel to cut away the screw, in with the 30 minute epoxy and now the calipers work perfectly And to thinning the back and sides from the supplied 3.5mm to the planned final thickness of 1.9mm. I'm sure there are better ways but, in the absence of a sander thicknesser, this is the best way for me. My little block plane: Then, once it was within 0.1mm or so of the target, smoothed out with the Mirka: Next was bending the first side and end: And, after lots of checking, using the long reach clamps to force the back into the radius- dish shape to glue it and the similarly shaped braces. Finally a reinforcement block for the florentine and we have a self-supporting curved back and the basic components done waiting for some kerfed (slotted) internal linings and the ebony top And, as I'm waiting for the kerfed strip, no excuse, I suppose, for starting the whole process again for the other side

Hmmm...not sure how that would work. Because the string goes through the middle of the cylinder, wouldn't all the strings behind the ones closest to the nut clash with their cylinders? It would be fun trying though - but not on this build

I can't really remember from the last ones I fitted, but I don't think so...

Lovely job.

Yes - new nut, I reckon

And actually, just a teeny drop of superglue at that, like on a nut - remember that the force on them is downwards, so there's nothing that is trying to move them once the string tension's on them. Doesn't need a lot of CA to stop them dropping out or moving when you take the strings off. Then, in the unlikely event of changing string type, you can just tap loose any that need repositioning and adjust and reglue.

Just seen @Hellzero 's post...he said the same thing but a bit more politely

These sorts of things are part of the 'nothing ventured, nothing gained' so it's worth walking away from it for a day or two to let your sub-conscience work through it a bit. That bridge looks as cool as fu a cucumber. And, actually, you know the intonation positions for the strings you are using. If it was me, I'd just super glue them in position...

The Switchcraft jack sockets have gained their reputation for the grade and consistency of the spring steel they use. I have replaced a lot of standard jack sockets on my own instruments and other peoples in the last 10 years...but to my recollection, I have never had to replace a Switchcraft one. The barrel sockets are another matter...even the Switchcraft barrel sockets fail eventually. I don't have many pro players I do work for, so it's not a statistically sound example, but all of the ones I do often ask for stereo sockets to be fitted as @Hellzero mentions above. Whereas on cheapo jack sockets it is usually the spring of the hot contact that looses its flex and cause the failures, the other weak spot on a mono jack is the ground contact. On a mono, this is wholly reliant on the barrel keeping contact with the jack stem. Using a stereo jack, the earth is connected to a proper spring contact. They are also noticeably harder to pull out with the old 'standing on the cable' trick. So I think this is the principle that the Pure Tone's have adapted and added to. It would be interesting to know the spring-steel grade they use - if it's good, then it is probably a decent belt and braces for high usage players. That said I would probably personally stick with stereo Switchcrafts for that category, simply because they are a known and proven quantity.

It needs a few photos, but essentially: - the top wing nut is the string clamping nut - the hole in the inner cylinder is where the string will go eventually - turning the knob at the bottom anticlockwise raises that inner cylinder plus wing nut out of the tuner, until the string hole appears (around 10mm) - the string is threaded through the hole in the inner cylinder, pulled tight and firmly clamped by the wing nut - turning the knob at the bottom clockwise pulls the cylinder back into the tuner body, taking both sides of the string with it. In doing so, the pitch of the string rises. - you can see in the photo of the strung up headstock that the inner cylinders with the wing nuts are at different heights. This is because the different strings require different degrees of tension to get them to pitch with, in this case, the top E pulled the furthest down They are remarkably easy to string up and extremely precise in their tuning. Real 'blue-sky thinking'

Yes - I'm looking forward to that too. At the moment it's in the 'I have no idea yet' category

Hi @ADAM ROBERTS Just spotted this (and @LowMoFo and @ezbass and @Aidan63 's kind references ) Clearly I can only comment on the problem with the neck and not your dispute with the maker. It's a complicated one because there can be a number of issues that can cause buzzing on the upper frets - not least the impact of the unusual weather this spring and summer. A pro-player I know had his 20 year old mandolin suddenly develop a severe neck bow (and they don't have truss rods). It was unplayable. When he got it out of the case a few weeks later to show me, it was almost back to normal. From what I understand, your truss rod is 'maxed out' - it does adjust, but the adjuster won't tighten any further and you are not able to add any more back bow in the event that it needs it in the future. While I can only generalise, some immediate thoughts: - It may not, of course, need any more back bow in the future. If the original problem was weather related, then you have had the frets levelled at it's most extreme case (which is good). When the weather returns to more normal levels, it is more likely that the rod will need loosening rather than tightening Or - as it is a one-way truss rod, there may have been a compression in the neck wood that the adjuster nut or the anchor plate bear against. Sometimes this can't be fixed. But often it can. 'Maxing out' the adjuster simply means that the adjuster has reached the end of the thread cut into the rod. So the fix with washers, is simply to unscrew the adjuster, put a suitably sized washer or two over the rod and then put the adjuster back on. The washers then bear up against the neck wood a couple of mm or so (however thick they are) sooner than the adjuster would have done, which gives the adjuster a few more turns before it bottoms against the end of the trussrod thread. This is a pretty standard fix and a google should find you the size of washers you need (and I'm sure there will be many Youtube clips on how it works and how to do it). However - if there is a structural failure in the rod or the wood that the internal rod components bear against, then it would need a rod replacement or internal repair...which sometimes isn't possible and always isn't easy. Let's put it this way - if it is a neck pocket based on Fender dimensions, it is usually cheaper and easier to fit a new neck. I hope this helps. Whereabouts in UK are you? Have a peep at the 'sticky' post of 'Basschatters willing to help others' or some title like that. There may be someone close to you who can have a look and give you a view what the issue is and how to fix it. Andy

This is already !ooking really nice. Can't wait!

Those are the steinbergers. They used to fit them on the low cost epiphone firebirds. Now they cost a small fortune. But they are the best tuners I've ever used. Completely different mechanism to anything I've seen before And unprompted, J's asked for them to be fitted to this

Pretty sure this is the general shape we're going for: