MoonBassAlpha

I use a plastic credit card as a fret rocker. Straddling 3 frets at a time only, the long side does the lower frets, and then switch to the short side as the frets get closer together. You should rock at the bass and treble sides of each fret, and the middle for good measure. High frets will often be at the edges and less so in the middle. Hope this helps!

I've got an EDA905 to look at. Complaint was that it was making a farting noise. It all checks out ok, turns out they were playing it through a guitar cab! It's a 5 string, and I think they were using a drop tuning too... Anyhow, the action was also 7mm, so I've shimmed the neck and now got it playing nicely with <1.7mm top to bottom! It's a really good neck! The remaining problem is one of the tuners has broken in the slot where the string sits. It still tunes and holds tune but doesn't look right. I can't find a single (not a set of 4) replacement in that finish, a smokey chrome. It's a Gotoh style right handed one (these things string up oddly). I'm wondering if anyone has better Google-Fu than me or has a spare knocking about in their parts drawer? Don't mind paying, of course!

6 pages in, in a topic covering loudness of cabs, and the expression "volume displacement" hasn't surfaced yet? Shame on you lot!

I was air bassing along to Good Times in my head at our morning stand-up meeting. My boss asked if I wouldn't mind stopping doing that. He's a bass player too, but I suppose there's a time and a place

Some pain killers can do that!

Another useful tip for while you're playing with the neck pocket is to slacken the neckplate screws off very slightly with the strings up at full tension (normal pitch). This uses the string tension to pull the neck hard into the end of the pocket, and can improve sustain and evenness across the strings. I recently did this with my Telecaster (guitar) and it made a noticeable difference. Obviously, do the screws up tight once you're done! Hth MBA

If you're worried about taking wood off with the tape you might try going over it with a hair dryer to soften the sticky. I find it works a treat!

Don't confuse turnover with profit though. ^

A medication box with am and pm sections would do 14 different ones, the lids snap closed, and have handy suggestions as to which plectrum to use on any given day!

That's an oddity, is it short scale? I can see the logic of only having 15 frets with a high C string, if that's how this is intended.

A Kramer 450B that weighed less than 8lbs would be sweet! I think mine was nearer 12 But nothing sounds quite the same. Pickups were a bit low output too, but that can be easily addressed.

My mate has just got the Presonus Eris 4.5, very pleased so far. Slightly over your budget new though

I read that old drum skins make excellent templates for spraying logos. Course, you have to have good cutting-out skills

To replace a faulty one in a Big Muff pi (Russian made). Dpdt, latching. I'm sure they're much of a muchness, but if any brand/source stands out, please let us know, cheers! MBA

Any idea what the body wood is? Apologies if I missed it earlier in the thread.

Does the spalting affect the structural strength when used as a body as opposed to a thin decorative top?

Impressive!

what's the cab setup at rehearsal? Is it higher off the ground so it's exciting the body of the bass more? I found a notch filter as used on acoustic guitar preamps killed the feedback on my mate's problematic Hofner Verithin Bass without affecting the overall tone.

Looks like a lovely studio! I hope you get great results!

change the buttons for the rubber style ones used on old-school rugby shirts.

My drummer had (hand) surgery and was is off playing and even driving for at least 8 weeks. Still a few to go, and even then there's no guarantee he'll be able to start up where he left off. I've been keeping myself busy with online collaboration with another mate who is getting back into music, so still playing bass and trying to play drums for him!

Attitude! (not having a go!)

Billy Sheehan?