-
Posts
187 -
Joined
-
Last visited
Content Type
Profiles
Forums
Events
Shop
Articles
Posts posted by FirstBass
-
-
Yeah, but the switch area is grainy and vague. I've tried zooming it
-
I know chances are slim, but does anyone have a modern player jazz that they'd be prepared to take a picture of for me?
I need the 4 position swich so I can see the wires clearly
The jpg that fender uk sent me is a bit grainy when I zoom into it.
I'd be v appreciative
-
Next time? 😁
-
Right!
ICEpower200ASC ordered from Profusion here in the UK
www.profusionplc.com
Remove all wiring connectors from the knackered, smelly board and note where they came from - took pics just in case
Undo 5 nuts and remove along with spring washers
CAREFULLY remove board with a bit of wiggling and patience
Fit new board in the big, empty gap. Power cables may need a little shifting to get it in
Breathe a sigh of relief when all the holes line up
Refit washers and nuts and nip down. I dabbed a bit of my favourite nail varnish on the threads to act as a virtual thread locker
Refit connectors
Refit lid
Connect up.... a quick pray and BINGO - we're all groovy
So... not cheap, but not difficult
The Shuttle 3.0 lives again
Thanks to everyone for their input
- 1
-
Thank you. I'd found that post, but for some reason the image wasn't showing
Are the red marks on the positional switch jumper wires?
I've soldered the wires back on and get no hum in positions 1+4 but a bit on 2+3
Am I to assume this is "normal" jazz behaviour? 😊
-
Hi.
I bought a 5 string modern player bass recently.
It has a 4 position switch to give you pickup combinations.
The pot was loose on the plate and has been spinning round...
There is a black and white wire dangling near the switch connections.
Does anybody have a wiring diagram of this model of bass please?
Thanks.
Jon.
-
-
Hello!
Do you still have this?
I'm keen.....
-
thank you everybody for your suggestions
I'm pretty sure it'll cost more than its worth to bring it back to life, but it definitely has sentimental value.
I'll shove it in a cupboard for a few months whilst i mourn my loss
-
I mustn't... but good luck with the sale!
- 1
-
-
must stop looking at this..... 😁
I'm only down the road in Wymondham too
Aaaaaaaaah!
-
it might be fun to bring it to a bass bash and see if we can blow it up.
I like your style..... 😁
- 1
-
Hi All
I made a boo boo with my lovely little Genz Shuttle 3.0
I was mildly drunk and testing a speaker using leads with spade connectors on the ends and one fell off and earthed on the front of the amp
It went quiet and then the standby light went red for a while and then back to blue
Phew!..... I thought
I turned it on later that evening and with the mute switch engaged or any 3 of the tone shaping buttons I get a hum through my cab
It also spikes when turning on
EQ works and there's plenty of volume on tap - its just the spike on startup and the hum when muted/tone shaped
I'm pretty certain the answer will be "fecked mate", but ......
Is there anywhere in the UK that could repair it?
I guess it all comes down to the cost. I didn't pay much for it, but it was my first "proper" amp and i'm rather attached to it
I've had a look inside, but there's nothing obvious - it did have "that smell" though
I'd appreciate any advice
Cheers
Jon
-
Hi
I like the look of grille cloth on bass cabs
I bought some from E Bay, but it was a swine to get it taught over the frame. It wasn't tough enough to protect the driver within a gigging cabinet
Does anybody know of a source/technique for achieving a sturdy cloth grille, or even a cloth that shrinks when heat is applied to it? (I've read about this online)
Appreciate any advice
-
Hi
I just got ahead of myself really and should've fitted this just before I fitted the top panel 😊
-
Me again
Bit more done
Cut the pipe with my band saw. Lifted the blade guide up as high as it would go and then gently rolled the tube round making sure I was hitting my 150mm markings
Came out a treat.
Roughed the plastic surface up with sandpaper and then used a cheap n nasty spray in very fine coats. Came out fine.
Stapled wadding in place
Have also fitted base, but no picture.
Next up is some routing of the edges
Crossover headache is looming. I'll crack it, but its my least fave part
So far so good
One point to make. The top panel brace has a notch out of it as per the plans. I glued this to the top panel before i'd built the cab up
The brace that goes inside the notch is not on the centre line of the baffle. So, my notch was not quite in the right place
I enlarged the notch so its fine now, but it might be worth leaving the brace off until you can see where it needs to be
hope that makes some kind of sense
This post was brought to you in association with Varta Batteries.....
- 3
-
-
-
-
ahhh..... the old "come in handy" eh? ☺️
-
I must admit that I felt awful when I looked the photo online rather than on my phone - What a dump! (the whole garage is like it... and my shed.... and trailer.... and greenhouse)
I think i've inherited this trait from my recently departed and massively missed father ☹️
We were never the tidiest of people when we got our teeth into a project
I always clean down between jobs, but this one seems to be taking the michael somewhat
Why do I need a battery for a vespa on the bench?
Right.... next bench pic will be MUCH tidier ☺️
I've just ordered the wood for a BFM Omni15 Tallboy too 😲. I feared that I may have this one done before the christmas break (definitely need a project to get my hands out of the quality street tin..)
Onwards and upwards!
- 2
- 1
-
-
Wiring for Fender Modern Player 5 String
in Repairs and Technical
Posted