3below

A good s/h db will be better value, someone else will have paid the initial depreciation and if you purchase wisely it will have been setup well at some point. The downside is that this bass takes time to find.

[quote name='Twincam' timestamp='1465787584' post='3070949'] The caps are the black can looking things and smaller blue ones. But keep away from the large ones. Is it me or does the resistor between the heatsinks look a little burnt on the board?? Since you didn't know which were the capacitors then I advise you fasten it back up take it too a tech as you really can get hurt. [/quote] +1 and the 2nd resistor above the inductor (greeny-blue coil) on the right hand side above big smoothing capacitors also looks a little 'charred'. (might be shadow in photo though). The big plus is that your Hartke is traditional discrete components on 'big' PCB. This means repairable at sensible costs. I doubt the components that need replacing cost more than £5, this money will be in labour costs, diagnosis and time.

[quote name='steve-bbb' timestamp='1465630622' post='3069711'] [b]Hubris + Hutzpah[/b] .... if anybody is looking for a new band name (1% royalty non-negotiable) [/quote] [quote name='Happy Jack' timestamp='1465635935' post='3069772'] But what if you were to spell Chutzpah correctly? [/quote] Chubris

Glue failure with a peavey Black Widow - age approx 25 years. The sponge 'air filter' inside the magnet / coil structure had also crumbled to dust / gunge.

Warwick Corvette - ash body. Not out of the ordinary but mine seems to weigh nothing in comparison to G&L and Kramer.

The similarity of names, business carried out (music) and operation within the same locality may constitute the common law tort of 'passing off' At this point seek some friendly legal advice as to what to do next.

[quote name='Sibob' timestamp='1465569891' post='3069364'] I just finished up recording an album at home for a singer, I simply plugged my Precision with flats into one of our (I work for Focusrite) Clarett 2Pres and it sounded fantastic. This isn't a sales pitch at all, but just an example of getting the right instrument, strings and interface for the project you're doing, and you don't need much else. When I sent the completely un-produced stems to the mix engineer, he commented that all he needed to do was to put on a light compressor on them and it sat in the track wonderfully. Si [/quote] Very similar to my experience. Gibson SG bass (with flats) direct into Focusrite or Sansamp then Focusrite. As per Sibob's engineer a small amount of compression is all that is needed. Joyo American pedal also works really well using same method for guitar recording. The biggest mistake I made to start with was recording with too much input level (it is not like my youth on tape). Record with low levels since there is virtually no background noise.

"T[color=#121212][font=helvetica, Helvetica, Arial, sans-serif][size=4]he similarities are "instantly recognisable to the ordinary observer"[/size][/font][/color] [color=#121212][font=helvetica, Helvetica, Arial, sans-serif][size=4]"Given the striking similarity between the ........... (the) defendants knew when writing, publishing, recording, releasing, and distributing ...... that they were infringing on a pre-existing musical composition.[/size][/font][/color] Insert Robert Johnson song and derivative blues works of choice. State that you are a descendant of Mr Johnson and consequently claim copyright infringement in all blues songs from all artists. How long before this one plays?

[quote name='AndyTravis' timestamp='1465417271' post='3068111'] This might sound stupid... Do you have a screwdriver you can change the ends on, you usually get the bits in a case with the handle and the bits pop into a hex hole at the end. I've found one of mine is a perfect fit (sans driver bit) for Rickenbackers... If not, it's a box spanner you're after. Try to measure it and look on eBay. They look like a little smoking pipe. Taylor, ric, Gibson and a few others use this type of adjuster. [/quote] +1 a 'box' spanner of the appropriate size. Mini (1/4"?) sockets sometimes fit but the socket walls are often to wide. Thin wall box spanner is the way forward, no mre than a few £.

[quote name='NancyJohnson' timestamp='1464898197' post='3063699'] Weird. I just wiggled the bridge pickup around and it's fully restored. Good you might think. No, not good. This harks back to an issue I had when I got the bass initially. Hmmm. [/quote] This suggests a faulty solder joint at the pickup might be the cause. It is fixable if you are skilled with the soldering iron. It might be a failed winding as neilp suggests. This is not fixable without a rewind or replacement.

Some very nice looking kit in super cosmetic condition, too good to use Silverface Bassman 100 (obvious), [url="http://www2.fender.com/support/articles/amplifier-product-dating/"]http://www2.fender.com/support/articles/amplifier-product-dating/[/url] and [url="http://www.ggjaguar.com/fendamp6.htm"]http://www.ggjaguar.com/fendamp6.htm[/url] will help dating the year of manufacture. Your spine hurts, my wallet is feeling the potential pain

Having owned both, the 300W version made the TNT series seem lightweight in comparison. Both did a fair bit of damage to the wheel arches in the boot space of my Citroen(s) at the time

[quote name='FuNkShUi' timestamp='1464689163' post='3061377'] Warwicks aren't popular at the minute. Some of the prices i've seen some German made ones go for are ridiculous. [/quote] Agree, cheap as chips and bargain basement value As stated earlier, for the money you are looking at you will have far too much choice. I have the same problems buying toothpaste and a toothbrush these days - am overwhelmed by choices. Looking at the tribute bass, get a Gibson SG bass (also 'cheap as chips' since they seem unpopular) and have the additional pickups fitted. I am finding my SG bass the one that gets most use these days.

[b]Marl[/b][font=arial, sans-serif][size=4] or marlstone is a calcium carbonate or lime-rich mud or mudstone which contains variable amounts of clays and silt. The dominant carbonate mineral in most [/size][/font][b]marls[/b][font=arial, sans-serif][size=4] is calcite, but other carbonate minerals such as aragonite, dolomite, and siderite may be present. Just sayin .......[/size][/font]

The Yamaha is super value, it will take quite a price hike to improve on it. Even that can be avoided with improved pickups (if needed). I have a Chinese Warwick rockbass corvette and the German version, there is not much in it. When you do feel the need for a 'better' bass BC is the place to look and buy. It might be worth asking a local BCer to give the Yamaha a lookover and setup - I am sure someone will free-gratis. Youtube is your friend, search for bass lines that you like and learn from the many, many talented people on it who explain / demo how to play. In my day (old man here) you listened to the 7" single and tried to work out what was being played. Explains why I am still learning

[quote name='Billy Apple' timestamp='1464288955' post='3058255'] Tfhhft! How many permutations can there be of a P Bass with flats? [/quote] Given how many have been made (and we all know they are different, never mind copies, tributes etc) x the range of flats available I suspect the answer is somewhat large No immediate answer on Google about how many Fender P basses have been made in total.

Bill Fitzmaurice will be along soon to explain why these top loading bins do not perform as well as horn loaded bins.

have been using Peavey with DDT for years. No ill effects yet some may disagree

Is it possible to get it rewound, plenty of pickup builders about. I suspect this will be far more cost effective than Novak or MEC replacement.

Penetrating oil, soak for a long while. Only problem is the penetrating oil will cost more than scrounging a s/h bridge saddle

[quote name='Twincam' timestamp='1463574015' post='3052433'] It ok I'm not stressed or wound up, slightly irritated maybe. A toothbrush? Is it an old bone one? Ivory? Please don't tell me it's plastic. [/quote] At £12,000 it should be made from unobtanium at the very least

Done being able to read helps