zig-zag Posted November 21, 2010 Share Posted November 21, 2010 (edited) I have this wonderful little amp for sale, reason being I need some money to fund an Orange Terror Bass. Bought new for 200 quid about 3 or 4 years ago, in pretty much new condition with a little bit of wear. Only problem is it cuts out at very low volume due to a wire not soldered properly to the input jack. Not a hard fix, just open it up and resolder. Crate footsitch for distortion channel/octaver included. Has a built in tuner and CD input. A solid little combo that's great for home practice/rehearsing, maybe even small venues. It's a pretty loud 50 watts. Here's some specs: Crate BT50: 50W and a 12" bass driver. 2 channels: a distortion channel with gain, shape, and level controls; and a clean channel with level, 4-band EQ, and an octave switch with level for boosting bottom end. It includes the CSF2 2-button footswitch for switching channels and kicking in the octave switch from the floor. Limiter, chromatic tuner, headphone jack, and CD inputs are also incorporated. Crate BT50 The Front Panel: INPUT: GAIN: SHAPE: Distortion channel. LEVEL: CHANNEL SWITCH: When using the footswitch: when this button is in the out position, the Clean channel is always active, and the footswitch turns the Distortion channel on and off, allowing you a blend of both channels. LEVEL: output level of the Clean channel, and as part of the Octave level control NOTE: employs an internal noise gate to keep residual noise to a minimum. Regardless of which channel is selected, the Clean channel's Level control (#6) must be turned up above "0" in order for the noise gate to trigger. LOW: LOW MID: HIGH MID: HIGH: OCTAVE: MASTER: CD INPUT: HEADPHONES: POWER: ELECTRONIC TUNER (top panel): constant, "real-time" tuning. The tuner is fully chromatic. The Rear Panel (not shown): AC LINE CORD: FOOTSWITCH: Crate CFP-2 for remote control of the channel selection/"blend" and octave on/off. EXTERNAL SPEAKER: internal speaker is disconnected when the external speaker jack is used. Crate BT50 Features: · Crate 12" bass driver · 50W RMS · Chromatic tuner · Distortion channel with gain, shape, and level · Clean channel with level, 4-band EQ, and foot-switchable octave with level · Limiter · Headphone jack · RCA CD input · CFS2 Footswitch Included · 21"W x 18"H x 14"D · 46 lbs. Crate BT50 Specifications: · Output Power Rating 50W RMS 2% THD, 4U · Gain Distortion Channel 104dB · Clean Channel 63dB · CD Inputs 37dB · Tone Range Low 21dB ® 50Hz · Lo Mid 23dB ® 150Hz · Hi Mid 18dB ® 1kHz · High 34dB ®10kHz · Signal to Noise Ratio 75dB · Input Impedance 220k ohms 220k ohms · Maximum Signal Accepted 15 volts peak-to-peak · Input Power Requirements 85VA 230VAC, 50/60Hz, 45VA 230VAC, 50/60Hz, 85VA · Internal Speaker Size 12" · Type Crate Custom Crate Custom · Magnet 30 oz. · Voice Coil 1.5" · RMS Rating 50 watts · Impedance 8 ohms · Size 21" H x 18" W x 14" D · Weight 46 lbs Looking for £80 ono, pick up only. Edited November 26, 2010 by zig-zag Link to comment Share on other sites More sharing options...
zig-zag Posted November 22, 2010 Author Share Posted November 22, 2010 Bump Link to comment Share on other sites More sharing options...
zig-zag Posted November 22, 2010 Author Share Posted November 22, 2010 Bump! Link to comment Share on other sites More sharing options...
zig-zag Posted November 24, 2010 Author Share Posted November 24, 2010 Bump Link to comment Share on other sites More sharing options...
zig-zag Posted November 26, 2010 Author Share Posted November 26, 2010 PRICE DROPPED TO £80! Link to comment Share on other sites More sharing options...
zig-zag Posted November 28, 2010 Author Share Posted November 28, 2010 I need to shift this guys, no one at all? Link to comment Share on other sites More sharing options...
Recommended Posts