DMX Posted February 27, 2011 Posted February 27, 2011 I've finally made the decision to let my Epifani 410 go - a Series I with the original B&C drivers. It's a fantastic cab, but I'm not playing gigs at the moment so it's way beyond my requirements, and I could do with releasing the cash. If you're on these boards then I'm sure you know the reputation of these cabs so I won't go on and on, but just to say this is a very clear and articulate cab with tonnes of bottom end. With the horn turned up it can sound very hi-fi, but with it down or off it gets a much more traditional sound. I've used it for rock and metal with excellent results (even if I do say so myself). This is an 8 ohm cab, but it's capable of such massive volume that I don't think that should put you off if you're after a 1 cab solution. I've been using it with a Trace V4 (200w valve amp) and never had the master past 4, putting out just under 200w if you believe the "output indicator" valve. I bought the cab 2nd hand about 5 years ago when it was in pristine condition. Since then it's done 20ish gigs and a handful of rehearsals, but also moved house a few time and so has picked a little cosmetic damage. As you will see from the photos, there are a couple of scratches on the nameplate and corner protectors and a few of the screws are a bit corroded. There are also one or two tiny paint chips on the grill, and you'll also notice a gap on the covering on the back of the cab. As far as I can tell it's always been like this, and the material is still well stuck down. It's in perfect working order. Given the not quite perfect condition and the slightly less sought-after 8 ohm rating, I'm after £400 collected from Banbury, Oxfordshire. I think this is a very fair price so am not open to offers. I will, however, consider delivering within 25 miles or so of Banbury or Brackley (where I work), so PM me to discuss if you'd require this. If you want any more info or opinions then let me know. Specs from Epifani website are below, and thanks for looking. David CONFIGURATION 4 x 10" 250W B&C Neo Drivers 100 Watt Bullet Tweeter Adjustable Tweeter Level Control IMPEDANCE 8 Ohms POWER RATING 1000 WRMS 2400 Watt Peak SPECS Response 40Hz - 16kHz Sensitivity 103dB (1W@1m) HARDWARE 2 x Speakon + 1/4" Output Connectors Lite Ply Poplar Plywood Dado Joint Construction Road-Ready Carpet Covering High-Impact Locking Corners Steel Recessed Handles 18 Gauge Steel Grill DIMENSIONS 26.25"H x 23"W x 17.75"D, or, 670mm H x 585mm W x 450mm D, 57lbs [attachment=73463:epi_main.JPG][attachment=73464:epi_badge.JPG][attachment=73465:epi_back.JPG] [attachment=73466:epi_corner.JPG][attachment=73467:epi_handle.JPG]
Lozz196 Posted February 27, 2011 Posted February 27, 2011 Darn, bought myself a new cab last week - would have taken this one like a shot as its much higher spec. As they say, its all in the timing - and mine was out
E sharp Posted February 27, 2011 Posted February 27, 2011 F**k a duck . This is an absolute steal . Doubt this'll last long .
DMX Posted February 27, 2011 Author Posted February 27, 2011 [quote name='E sharp' post='1143959' date='Feb 27 2011, 10:32 PM']F**k a duck . This is an absolute steal . Doubt this'll last long .[/quote] It hasn't! On hold, pending etc.
JCB Posted February 28, 2011 Posted February 28, 2011 [quote name='DMX' post='1143963' date='Feb 27 2011, 10:34 PM']It hasn't! On hold, pending etc.[/quote] Hi David That didn't take long! Glad to see you moved it quickly... cheers, Jonathan
markstuk Posted February 28, 2011 Posted February 28, 2011 If this falls through, I'll have it .... Cheers Mark [quote name='JCB' post='1144346' date='Feb 28 2011, 12:07 PM']Hi David That didn't take long! Glad to see you moved it quickly... cheers, Jonathan[/quote]
DMX Posted February 28, 2011 Author Posted February 28, 2011 (edited) Cheers guys. I think it took me longer to write the ad than it did for the cab to sell! Edited February 28, 2011 by DMX
Recommended Posts