willyf87 Posted June 10, 2011 Share Posted June 10, 2011 Need some advice. The output jack on my bass appears to be acting up in a strange way in the sense that it's cutting off some of the high end. If i twiddle the cable (I have tried a couple now with the same problem) its seems to come come back. If i wrap the cable around through the strap (as you do ) and wedge it tight it seems to eliminate the problem. I'm assuming the best fix is a new connector but just wanted to know if it could be anything else. If the cable moves around in the socket it makes a pretty nasty crackle. Haven't hand a chance to open it up yet wonder if its a dodgy solder joint. Oh and its a fender mex precision standard. Quote Link to comment Share on other sites More sharing options...
Big_Stu Posted June 10, 2011 Share Posted June 10, 2011 Not necessarily. If you get an improvement by moving your jack plug about it could be just teh socket has bent loose. If you can get the jack plate & socket out easily try bending the hot pin inwards to improve the "click" of your jack going in (not too much though), the bit the tip of your jack clicks onto. Do with with a couple of pairs of pliers, if you just use one you risk cracking the insulating layer which will short out (knacker) the jack socket. Maplins sell stacks of different kinds of jack sockets (Neutriks) for peanuts if needed. Quote Link to comment Share on other sites More sharing options...
Ou7shined Posted June 10, 2011 Share Posted June 10, 2011 Might just need soldering. If it's a barrel jack then yes maybe it will need replacing. You won't be able to tell until you open her up. Quote Link to comment Share on other sites More sharing options...
Monckyman Posted June 11, 2011 Share Posted June 11, 2011 Does sound like sh*t on the contacts though Quote Link to comment Share on other sites More sharing options...
flyfisher Posted June 11, 2011 Share Posted June 11, 2011 Guitar jacks get a lot of use and they don't last forever. As mentioned above, new sockets cost peanuts and if you can solder it's an easy repair that can make a big difference. If you can't solder then this might be an ideal opportunity to learn - it's not that difficult. But, if you don't fancy it then it shoudn't be too hard to find someone to re-place the socket for you. Ask at your local music shop if you don't know anyone who can do it for you. Quote Link to comment Share on other sites More sharing options...
Count Bassy Posted June 12, 2011 Share Posted June 12, 2011 [quote name='Big_Stu' post='1264232' date='Jun 10 2011, 06:29 PM']Not necessarily. If you get an improvement by moving your jack plug about it could be just teh socket has bent loose. If you can get the jack plate & socket out easily try bending the hot pin inwards to improve the "click" of your jack going in (not too much though), the bit the tip of your jack clicks onto. Do with with a couple of pairs of pliers, if you just use one you risk cracking the insulating layer which will short out (knacker) the jack socket. Maplins sell stacks of different kinds of jack sockets (Neutriks) for peanuts if needed.[/quote] Plus, twist a clean (and dry) 'scotchbrite into it by 10mm or so to clean up the inside of the earth sleeve - can make a big difference. Only works on sockets where the earth contact is made via a solid sleeve. - don't try it where the earth contact is itself a sprung contact. Quote Link to comment Share on other sites More sharing options...
Count Bassy Posted June 12, 2011 Share Posted June 12, 2011 [quote name='Big_Stu' post='1264232' date='Jun 10 2011, 06:29 PM']Not necessarily. If you get an improvement by moving your jack plug about it could be just teh socket has bent loose. If you can get the jack plate & socket out easily try bending the hot pin inwards to improve the "click" of your jack going in (not too much though), the bit the tip of your jack clicks onto. Do with with a couple of pairs of pliers, if you just use one you risk cracking the insulating layer which will short out (knacker) the jack socket. Maplins sell stacks of different kinds of jack sockets (Neutriks) for peanuts if needed.[/quote] Plus, twist a clean (and dry) 'scotchbrite into it by 10mm or so to clean up the inside of the earth sleeve - can make a big difference. Only works on sockets where the earth contact is made via a solid sleeve. - don't try it where the earth contact is itself a sprung contact. Quote Link to comment Share on other sites More sharing options...
Jean-Luc Pickguard Posted June 13, 2011 Share Posted June 13, 2011 If you replace the jack (& in this case it sounds like its the standard 'open' type), be sure to get a proper branded switchcraft one, not something crappy from maplins. Quote Link to comment Share on other sites More sharing options...
Big_Stu Posted June 13, 2011 Share Posted June 13, 2011 [quote name='Jean-Luc Pickguard' post='1267768' date='Jun 13 2011, 07:26 PM']not something crappy from maplins.[/quote] Maplins have stacks in by Neutrik, which I've never had any problems with. The last sockets I bought were £1.99 each; still going strong after a lot of use. With my first bass as a teenager there wasn't a nearby guitar shop, I asked at a TV repair shop if they could solder a switch for me - and they did it for nothing, said it made an interesting change for them. Quote Link to comment Share on other sites More sharing options...
Ross Posted June 14, 2011 Share Posted June 14, 2011 I bought an 80p cheapo jack from "pikeys second hand and electronics" about a month ago as a temporary fix, already starting to lose contact. Invest in a quality component. Quote Link to comment Share on other sites More sharing options...
willyf87 Posted June 15, 2011 Author Share Posted June 15, 2011 cheers for all the answers guys!! I opened the bass up last night it all looks fine but the jack contact (if thats what you call it) was looking very straight so I bent it inwards a bit, seems to have done the trick. If I have any more problems I'll straight up replace it. Quote Link to comment Share on other sites More sharing options...
Monckyman Posted June 15, 2011 Share Posted June 15, 2011 Happy Daze! Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.