Jump to content
Why become a member? ×

rane dc24 - help


MOXYBASS
 Share

Recommended Posts

[color=#141414][font=verdana, geneva, lucida,]I'm doing something wrong ................... getting no effect from my Rane DC24 [/font][/color]
The manual is not the easiest to follow

[color=#141414][font=verdana, geneva, lucida,]Power light = on[/font][/color]
[color=#141414][font=verdana, geneva, lucida,]Crossover Engage switch = [/font][/color][i]in[/i]
[i]Separate/Combine Outputs switch = [i]combine[/i][/i]
[color=#141414][font=verdana, geneva, lucida,]bypass button = [/font][/color][i]out[/i]

[color=#141414][font=verdana, geneva, lucida,]All I am getting is amp sound with no effect[/font][/color][color=#141414][font=verdana, geneva, lucida,] [/font][/color]

[color=#141414][font=verdana, geneva, lucida,]Using Markbass little amp - on rear of the amp there is [/font][/color][i]effect send[/i][color=#141414][font=verdana, geneva, lucida,] and [/font][/color][i]effect return[/i][color=#141414][font=verdana, geneva, lucida,] what do these plug into on the rane - I have tried several combinations.[/font][/color]

Edited by MOXYBASS
Link to comment
Share on other sites

Excuse my question, but what kind of "effect" are you expecting? I`m not a user of this piece of gear but i belive this a rack unit compressor/limiter. This should sound as transparent as possible.

Hope this helps: http://www.ovnilab.com/reviews/dc24.shtml

Edited by A.G.E.N.T.E.
Link to comment
Share on other sites

From the manual:

"COMPRESSOR THRESHOLD control: determines above what input level the Compressor functions. Full clockwise rotation disables the Compressor entirely. The LED illuminates yellow any time the input signal exceeds the threshold level set by this control."

Where have you set the threshold? If you turn down the threshold, does the yellow LED flash with signal?

Link to comment
Share on other sites

[color=#141414][font=verdana, geneva, lucida,]I have set the Rane as below[/font][/color]

[color=#141414][font=verdana, geneva, lucida,]REAR[/font][/color]
[color=#141414][font=verdana, geneva, lucida,]CH2[/font][/color]
[color=#141414][font=verdana, geneva, lucida,]combine selected[/font][/color]
[color=#141414][font=verdana, geneva, lucida,]4db[/font][/color]
[color=#141414][font=verdana, geneva, lucida,]high combine out connect to return effect in amp[/font][/color]

[color=#141414][font=verdana, geneva, lucida,]CH1[/font][/color]
[color=#141414][font=verdana, geneva, lucida,]4db[/font][/color]
[color=#141414][font=verdana, geneva, lucida,]CH1/crossover in - connected to send effect in amp[/font][/color]

[color=#141414][font=verdana, geneva, lucida,]-----------------------------------[/font][/color]

[color=#141414][font=verdana, geneva, lucida,]FRONT[/font][/color]
[color=#141414][font=verdana, geneva, lucida,]CH1[/font][/color]
[color=#141414][font=verdana, geneva, lucida,]Gate Threshold = full clockwise[/font][/color]
[color=#141414][font=verdana, geneva, lucida,]ratio =1:1[/font][/color]
[color=#141414][font=verdana, geneva, lucida,]Compressor = 0[/font][/color]
[color=#141414][font=verdana, geneva, lucida,]ratio = 1:1[/font][/color]
[color=#141414][font=verdana, geneva, lucida,]Limiter = full clockwise[/font][/color]
[color=#141414][font=verdana, geneva, lucida,]Output = 0 [/font][/color]
[color=#141414][font=verdana, geneva, lucida,]Bypass button = out[/font][/color]

[color=#141414][font=verdana, geneva, lucida,]crossover = 100[/font][/color]
[color=#141414][font=verdana, geneva, lucida,]Mode = dual[/font][/color]

[color=#141414][font=verdana, geneva, lucida,]CH2[/font][/color]
[color=#141414][font=verdana, geneva, lucida,]Gate Threshold = full clockwise[/font][/color]
[color=#141414][font=verdana, geneva, lucida,]ratio =1:1[/font][/color]
[color=#141414][font=verdana, geneva, lucida,]Compressor = 0[/font][/color]
[color=#141414][font=verdana, geneva, lucida,]ratio = 1:1[/font][/color]
[color=#141414][font=verdana, geneva, lucida,]Limiter = full clockwise[/font][/color]
[color=#141414][font=verdana, geneva, lucida,]Output = 0 [/font][/color]
[color=#141414][font=verdana, geneva, lucida,]Bypass button = out[/font][/color]

[color=#141414][font=verdana, geneva, lucida,]Set above = distorted sound (like fuzz effect) - if bypass CH2 distortion goes away[/font][/color]
[color=#141414][font=verdana, geneva, lucida,]Comression threshold light does not come on at all even when moving it to diff levels[/font][/color]

Link to comment
Share on other sites

  • 3 weeks later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

 Share

  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...