Cosmo Valdemar Posted May 11, 2015 Share Posted May 11, 2015 I've seen countless references to players varying the volume on a Jazz bass to achieve a seemingly endless blend of tones. Sounds logical. Problem is, I can't seem to be able to do it! It seems that whenever I begin to turn down either volume, there is very little 'turn' before the other pickup becomes dominant. It doesn't feel like I'm turning a pickup down, more like I'm switching it off. The rest of the turn makes very little difference to the overall tone of the bass. I usually ride the front pickup on it's own so it's never been much of an issue but I can't help feeling there are some wonderful tones I'm missing out on - particularly all this talk of the 'sweet spot'. I've owned several Jazzes over the years, not all Fenders, and I always have the same problem. I currently play a Lakland DJ4 and a Fender MIM 60s reissue. I've recently parted company with a Road Worn - same problem. What am I doing wrong?! Quote Link to comment Share on other sites More sharing options...
JapanAxe Posted May 11, 2015 Share Posted May 11, 2015 Glad to hear it's not just me! When i had a Jazz I ended up replacing one of the volume pots with a pickup selector switch and using the other as a master volume. Sweet spot? Load of b0ll0cks! Quote Link to comment Share on other sites More sharing options...
Sammers Posted May 11, 2015 Share Posted May 11, 2015 Have you thought about installing a blend pot in place of 1 of the volumes? Both my Sandberg (Passive) & Mike Lull (Bartolini Pre) have this setup and both have a very even blend, it's awesome for adjusting on the fly I've no experience with V/V/T jazzes though so have never come across your issue! Quote Link to comment Share on other sites More sharing options...
Conan Posted May 11, 2015 Share Posted May 11, 2015 [quote name='Cosmo Valdemar' timestamp='1431343108' post='2770125'] I've seen countless references to players varying the volume on a Jazz bass to achieve a seemingly endless blend of tones. Sounds logical. Problem is, I can't seem to be able to do it! What am I doing wrong?! [/quote] Try speaking to KiOgon on here. There may be a wiring or capacitor mod that is easily made that will give you more control... Then again, I may be mistaken! Quote Link to comment Share on other sites More sharing options...
Captain Rumble Posted May 11, 2015 Share Posted May 11, 2015 Talk to KiOgon he made a kit up for my mim jazz vol blend tone much better arrangement than the original vvt absolutely recommend his work Quote Link to comment Share on other sites More sharing options...
Roger2611 Posted May 11, 2015 Share Posted May 11, 2015 I am the same, I can't find the sweet spot on a Jazz much the same as the G spot on the wife....I think it's a myth Quote Link to comment Share on other sites More sharing options...
RickyV Posted May 11, 2015 Share Posted May 11, 2015 Same with mine, must be normal with a VVT set up. Just whack them both up full. Works for me. Quote Link to comment Share on other sites More sharing options...
miles'tone Posted May 11, 2015 Share Posted May 11, 2015 I had the same problem. It's got to be a myth. The answer would be to install linear taper pots and ditch the standard audio taper. Linears give a clean sweep of volume for the entire turn of the knob. God knows why Fender don't use them, it's not like they cost anymore. Quote Link to comment Share on other sites More sharing options...
HowieBass Posted May 11, 2015 Share Posted May 11, 2015 +1 for a volume with blend arrangement - lots of flexibility with this on my Squier Deluxe Jazz Active. Quote Link to comment Share on other sites More sharing options...
ikay Posted May 11, 2015 Share Posted May 11, 2015 (edited) Part of the issue with standard VVT wiring is that when both pups are fully 'on' the pickup impedances interact with each other. As you back one pup off this introduces a resistance between the pups and the interaction/loading stops. This all happens in the first few degrees of turning the pot and the overall effect is that the sound seems to 'switch' to the dominant pickup with very little blend in between. However, there ARE loads of useful blended sounds in this very small area. Once you get used to the idea that you just need to move the pot a tiny amount you will start hearing lots of different tones. This is where the 'sweet spots' are. Here's a trick worth trying - instead of having both vols fully open, back them both off very slightly. This introduces some resistance between them and stops them interacting. Use this as your start point and you should find that backing each vol off further will result in a slightly more smooth change in tone. Another way of preventing the pickup impedances interacting is to wire a small resistor (eg. 25k) in series between the hot wire from each pickup and their respective pots. This effectively does the same thing as backing both vols off a touch. If all that sounds too fiddly and doesn't do what you expect then go active and get a buffered blend! Personally I like the subtleties and slight quirkiness of a VVT configuration. It lets the full character of each pickup come through. A blend pot can sound a bit bland in comparison. But in the end, as with everything to do with tone, it's very personal and down to what works for you. Edited May 11, 2015 by ikay Quote Link to comment Share on other sites More sharing options...
dmccombe7 Posted May 11, 2015 Share Posted May 11, 2015 Same here. Always run them full on and vary tone control. I have tried bringing both back 25% and that gives a more subtle tone change but to get the hard driven edge of the jazz you need both full on. Good to see its not just me then. Dave Quote Link to comment Share on other sites More sharing options...
miles'tone Posted May 11, 2015 Share Posted May 11, 2015 [quote name='ikay' timestamp='1431367025' post='2770583'] Part of the issue with standard VVT wiring is that when both pups are fully 'on' the pickup impedances interact with each other. As you back one pup off this introduces a resistance between the pups and the interaction/loading stops. This all happens in the first few degrees of turning the pot and the overall effect is that the sound seems to 'switch' to the dominant pickup with very little blend in between. However, there ARE loads of useful blended sounds in this very small area. Once you get used to the idea that you just need to move the pot a tiny amount you will start hearing lots of different tones. This is where the 'sweet spots' are. Here's a trick worth trying - instead of having both vols fully open, back them both off very slightly. This introduces some resistance between them and stops them interacting. Use this as your start point and you should find that backing each vol off further will result in a slightly more smooth change in tone. Another way of preventing the pickup impedances interacting is to wire a small resistor (eg. 25k) in series between the hot wire from each pickup and their respective pots. This effectively does the same thing as backing both vols off a touch. If all that sounds too fiddly and doesn't do what you expect then go active and get a buffered blend! Personally I like the subtleties and slight quirkiness of a VVT configuration. It lets the full character of each pickup come through. A blend pot can sound a bit bland in comparison. But in the end, as with everything to do with tone, it's very personal and down to what works for you. [/quote] Excellent post there, nice one 👍. I will try this next time I have a go on a Jazz (sold mine a long time ago). Quote Link to comment Share on other sites More sharing options...
paul_5 Posted May 11, 2015 Share Posted May 11, 2015 [quote name='RickyV' timestamp='1431366460' post='2770562'] Same with mine, must be normal with a VVT set up. Just whack them both up full. Works for me. [/quote] THis, except I've bypassed the Tone pot, as it was always ever 'whacked up' too... Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.