Muppet Posted June 18, 2015 Share Posted June 18, 2015 New (to me) jazz bass. Vintage BBOT bridge with slot head saddle height screws. I go to set my string height and I find the buggers have been glued in place. Is this madness? Any ideas about how to remove the glue, heat maybe or something else? steve Quote Link to comment Share on other sites More sharing options...
ikay Posted June 18, 2015 Share Posted June 18, 2015 (edited) Sure it's glue and they're not rusted in? In which case use a little WD40. If they're glued in then depends what glue was used. Acetone (eg. nail varnish remover) will soften superglue so may be worth a try. If you use heat then don't directly use an open flame which might discolour the saddles. Edited June 18, 2015 by ikay Quote Link to comment Share on other sites More sharing options...
Muppet Posted June 18, 2015 Author Share Posted June 18, 2015 Definitely glue! A little heat on it and it's got that superglue smell going on... Someone obviously set it up to their specs and decided it wasn't every going to change! Will persevere.. Quote Link to comment Share on other sites More sharing options...
brensabre79 Posted June 19, 2015 Share Posted June 19, 2015 Sometimes they slip, my 70s Jazz used to. I was a bit more drastic though, I put a Badass bridge on instead Quote Link to comment Share on other sites More sharing options...
Muppet Posted June 19, 2015 Author Share Posted June 19, 2015 Thanks, yes my research suggests that people often glue the screws when they slip, or, as you have done, swap the bridge out completely! Last night I gently heated the saddles over the gas stove and the glue melted enough for me to turn out the screws. The glue hardened again but brittle so it could be chipped off with a watchmakers screwdriver with no damage to the saddle itself. Quote Link to comment Share on other sites More sharing options...
bassbiscuits Posted July 5, 2015 Share Posted July 5, 2015 I liking the idea of carefully heating the saddle/screw to help dissolve the glue. I've got some old bridge saddles like that which won't budge. I'll give it a very careful try. Quote Link to comment Share on other sites More sharing options...
pfretrock Posted July 5, 2015 Share Posted July 5, 2015 Another reason to get a soldering iron.......safer than a gas stove. Quote Link to comment Share on other sites More sharing options...
Muppet Posted July 5, 2015 Author Share Posted July 5, 2015 [quote name='pfretrock' timestamp='1436099418' post='2814891'] Another reason to get a soldering iron.......safer than a gas stove. [/quote] In my defence I did try the soldering iron first, but it didn't heat the whole saddle enough to melt all the glue in the screw threads. Quote Link to comment Share on other sites More sharing options...
Muppet Posted July 5, 2015 Author Share Posted July 5, 2015 [quote name='bassbiscuits' timestamp='1436087930' post='2814775'] I liking the idea of carefully heating the saddle/screw to help dissolve the glue. I've got some old bridge saddles like that which won't budge. I'll give it a very careful try. [/quote] Low heat, long nosed pliers and undo the screw if you can whilst held over the heat. Works a treat. Quote Link to comment Share on other sites More sharing options...
bassbiscuits Posted July 5, 2015 Share Posted July 5, 2015 Cool that's my little job for this evening then...! Quote Link to comment Share on other sites More sharing options...
King Tut Posted July 6, 2015 Share Posted July 6, 2015 I've occasionally used loktite on fender bridges that 'self adjust' but glue seems rather extreme! Quote Link to comment Share on other sites More sharing options...
pfretrock Posted July 6, 2015 Share Posted July 6, 2015 [quote name='Muppet' timestamp='1436111582' post='2815032'] In my defence I did try the soldering iron first, but it didn't heat the whole saddle enough to melt all the glue in the screw threads. [/quote] Reckon a 50W temperature controlled iron poked into the screw head should do it, but not all irons are like that. Worth a try though. Quote Link to comment Share on other sites More sharing options...
pfretrock Posted July 6, 2015 Share Posted July 6, 2015 [quote name='King Tut' timestamp='1436170812' post='2815452'] I've occasionally used loktite on fender bridges that 'self adjust' but glue seems rather extreme! [/quote] Loktite may be extreme if you use the wrong grade. Nail varnish is Ok, a nice pink color Quote Link to comment Share on other sites More sharing options...
paul_5 Posted July 6, 2015 Share Posted July 6, 2015 I've heard of people putting nail varnish in there to do the same job. Not sure I'd glue stuff though, and I'd [i]definately[/i] not Loctite® it unless I absolutely, never, unequivocally didn't want it to move again. Ever. Quote Link to comment Share on other sites More sharing options...
Count Bassy Posted July 9, 2015 Share Posted July 9, 2015 [quote name='paul_5' timestamp='1436176018' post='2815520'] I've heard of people putting nail varnish in there to do the same job. Not sure I'd glue stuff though, and I'd [i]definately[/i] not Loctite® it unless I absolutely, never, unequivocally didn't want it to move again. Ever. [/quote] Depends on the grade of locktite. (we're talking, nut-lock/stud-lock varieties here, not "Superglue"). Quote Link to comment Share on other sites More sharing options...
BassBod Posted July 16, 2015 Share Posted July 16, 2015 Another method is take the screw out...put a little superglue on, then let it dry for an hour before replacing it. Often this is enough to stop it undoing over time..but without glueing it in place. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.