JCBass Posted July 28, 2016 Share Posted July 28, 2016 I recently bought an old battered no-name precision off of Fleabay to relic and use as a back up, however as can be the case with eBay, there's an issue with the electronics, there's only a buzzing sound when I plug in! As a disclaimer, I'm an absolute amateur when it comes to electronics, no knowledge, so excuse any stupid or blatant things I say. I looked up a wiring diagram and compared it to what's actually present on my bass and it appears that the Tip (hot output) is connected to the inner portion of the jack socket (should be connected to the outer I believe?) and that there is no wire (sleeve?) going from the tone pot to the jack socket. Also the ground wire is connected to both pots and the Jack socket (on the inner ring where the hot output should be), I don't know if this is correct? Quote Link to comment Share on other sites More sharing options...
hubrad Posted July 28, 2016 Share Posted July 28, 2016 If the jack socket was wired back to front you should still get a note, just extra noisy. The pics aren't clear enough to be certain what's going on, but you can eliminate the pots by unsoldering the pickup and holding the wires onto one plug of a guitar cable. If that works, chuck the pots and put fresh ones in. If the pickup is problematic, get a used decent pickup in the Marketplace and start over. Quote Link to comment Share on other sites More sharing options...
mrn1989 Posted July 28, 2016 Share Posted July 28, 2016 (edited) If your not confident, then just go for the simple replace the lot option....although it would be good to teach yourself Here is a cheap easy kit [url="http://www.ebay.co.uk/itm/precision-p-style-bass-solderless-guitar-wiring-harness-kit-orange-drop-tone-cap-/131885801855?hash=item1eb501a17f:g:bbYAAOSwnLdWqoCf"]http://www.ebay.co.u...bYAAOSwnLdWqoCf[/url] Edited July 28, 2016 by mrn1989 Quote Link to comment Share on other sites More sharing options...
KiOgon Posted July 28, 2016 Share Posted July 28, 2016 Or - you could get yourself a top notch kit from someone right here who is always there when you need any help Please check my feedback Quote Link to comment Share on other sites More sharing options...
HazBeen Posted July 28, 2016 Share Posted July 28, 2016 +1 for kiOgon and for better pics. Difficult to tell from these, buzzing sound may be pickup or ground related if I am guessing blind. Quote Link to comment Share on other sites More sharing options...
Grangur Posted July 28, 2016 Share Posted July 28, 2016 Those pots are old. I also don't like bare wires at all - They're too open to short-circuits. If I were you I'd replace the lot. Problem 1: you're not me and your wiring/soldering skills may not be so good. There's no reason why you can't buy the parts and learn. I did. And if it goes wrong we can advise. Or, you could buy a harness from KiOgon who, I believe, does a top-job. Good luck whatever you chose to do. Quote Link to comment Share on other sites More sharing options...
BassBunny Posted July 29, 2016 Share Posted July 29, 2016 If you are not confident about doing it yourself, whereabouts do you live? A BassChatter may be able to replace everything, (as it looks like it needs it), and you can watch and learn. Or go the KiOgon route. Quote Link to comment Share on other sites More sharing options...
Paul S Posted July 29, 2016 Share Posted July 29, 2016 Kiogon route is what I would do. I've bought many looms from John over the past few years and always had exemplary service and top quality product. And they couldn't be easier to fit. Quote Link to comment Share on other sites More sharing options...
Twincam Posted July 29, 2016 Share Posted July 29, 2016 I think you should as said test the pu as stated in a post above. Buy a soldering iron and the rest of the parts and make one up yourself. However as others have said asking kiogon to make you one up is a good idea also as it will be done right the first time and will be a better job than your first try and it probably won't be as expensive as getting the bits and a decent soldering iron together Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.