umcoo Posted October 23, 2016 Share Posted October 23, 2016 Hi all, I'm wanting to run my jazz bass in series, but I'm struggling to find a wiring diagram. I'm not wanting to have a parallel/series switch or push/pull pot. Just wanting series as 'standard'. Any help, guys? Cheers all Quote Link to comment Share on other sites More sharing options...
Woodinblack Posted October 23, 2016 Share Posted October 23, 2016 (edited) Well, its pretty easy. Just take the white wire from the second down volume center (the bridge hot wire), take the black wire from the neck pickup that is wired to the case of the pot (or some other earthing point), disconnect it from there and connect those white and black wires together (insulating them), and bobs your uncle. Then volume will be the first pot and the second old bridge volume won't do anything. It sounds quite good. Edited October 23, 2016 by Woodinblack Quote Link to comment Share on other sites More sharing options...
Grangur Posted October 23, 2016 Share Posted October 23, 2016 You mean in series with just one volume and tone with both pups connected 100% of the time? If so, then simply connect the neck pup "earth" to the bridge pup "hot" and then wire it as you would wire a Precision. Quote Link to comment Share on other sites More sharing options...
paul_5 Posted October 23, 2016 Share Posted October 23, 2016 Each pickup will have a black and white wire (your colours may vary, but they'll be different colours), take the wire that is soldered to the back of the neck volume control (ground) off the back of the pot, so it's floating loose inside the bass. Then remove the wire that goes to the middle lug of the bridge pickup off the centre lug and join it to the first wire that you removed. Make sure that it's isolated (electrician's tape or similar) and that's it. Effectively you'll have a black and a white joined together at the end. Quote Link to comment Share on other sites More sharing options...
Grangur Posted October 23, 2016 Share Posted October 23, 2016 Seeing all 3 replies are the same. It's a shame we all didn't know someone else was answering. Quote Link to comment Share on other sites More sharing options...
Woodinblack Posted October 23, 2016 Share Posted October 23, 2016 Well, at least it shows consistency! Quote Link to comment Share on other sites More sharing options...
umcoo Posted October 23, 2016 Author Share Posted October 23, 2016 I knew I could rely on you all! Thanks all, much appreciated Quote Link to comment Share on other sites More sharing options...
Norris Posted October 24, 2016 Share Posted October 24, 2016 [quote name='Grangur' timestamp='1477254282' post='3160941'] Seeing all 3 replies are the same. It's a shame we all didn't know someone else was answering. [/quote] I think that qualifies as a consensus Quote Link to comment Share on other sites More sharing options...
goingdownslow Posted October 24, 2016 Share Posted October 24, 2016 (edited) Gibson used this method on a Thunderbird, retaining both volume controls. [attachment=230641:Series pickup wiring.JPG] Edited to add this.. [attachment=230642:Series pickup wiring 2.JPG] Edited October 24, 2016 by goingdownslow Quote Link to comment Share on other sites More sharing options...
umcoo Posted October 24, 2016 Author Share Posted October 24, 2016 Do i need to splice and solder the 2 wires together, or can i just wrap them together in tape or heat shrink? Quote Link to comment Share on other sites More sharing options...
Thunderbird Posted October 24, 2016 Share Posted October 24, 2016 Why not just use a small terminal block then it is easy to swap back if you want to Quote Link to comment Share on other sites More sharing options...
Grangur Posted October 24, 2016 Share Posted October 24, 2016 [quote name='umcoo' timestamp='1477321422' post='3161395'] Do i need to splice and solder the 2 wires together, or can i just wrap them together in tape or heat shrink? [/quote] Now't wrong with twisting and tape, or a terminal block. Anything is good as long as there's a good electrical connection. Quote Link to comment Share on other sites More sharing options...
umcoo Posted October 24, 2016 Author Share Posted October 24, 2016 I've got a Kiogon wiring harness in there, so I guess I could just stick both wires into an 'unused' block on the terminal? Quote Link to comment Share on other sites More sharing options...
umcoo Posted October 24, 2016 Author Share Posted October 24, 2016 Scrap that, there aren't any unused ones Quote Link to comment Share on other sites More sharing options...
Grangur Posted October 24, 2016 Share Posted October 24, 2016 Have chat with Kiogon. He's a helpful guy, He'll tell you what to do. When you go in, series and knock out a volume there may be other changes you need in the harness. I'm sure there will be changes you need. If you're not into wiring, maybe he should make you a new harness? Quote Link to comment Share on other sites More sharing options...
umcoo Posted October 24, 2016 Author Share Posted October 24, 2016 I just soldered the two wires together and heat shrunk it so it's a good solid connection. Wow, pretty big difference in sound. Liking it Thanks for the help guys, I'm clueless around stuff like this. Quote Link to comment Share on other sites More sharing options...
Grangur Posted October 24, 2016 Share Posted October 24, 2016 So I guess what you have now is a P-bass with big coils. Nice one! Quote Link to comment Share on other sites More sharing options...
umcoo Posted October 24, 2016 Author Share Posted October 24, 2016 In the shape of a Jazz Bass Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.