Geek99 Posted February 21, 2018 Share Posted February 21, 2018 I've bought some jazz bass pickups on ebay. They have codes 048612 & 048613 underneath which I know are fender codes for the bobbins - they have "59" or "se" handwritten on in white (its a little unclear) Standard spec for US jazz is allegedly Neck 8.3 kohm and Bridge 7.8kOhm they look fine visually I used a multi-meter and measured at the soldered contacts neck 6.9 k Ohm bridge 7.57 k Ohm can anyone tell me what the effect of the resistances being reversed (ie relatively between the two positions) is ? If I've measured wrongly please advise where I should correct my technique - I used the 20 kOhm range. thanks Quote Link to comment Share on other sites More sharing options...
KiOgon Posted February 21, 2018 Share Posted February 21, 2018 (edited) It sounds like you are measuring correctly, you'll probably find the 6.9k may be a bit less output than the bridge, so - trial and error - it might work out ok depending on how you like to mix the pups. OTOH of course, it may be the wrong pick up, or even be short of a few windings! Cheerz, John Edited February 21, 2018 by KiOgon Quote Link to comment Share on other sites More sharing options...
Bassalarky Posted February 21, 2018 Share Posted February 21, 2018 I would normally expect the neck pickup to be slightly lower than the bridge. The string vibrates more in the neck position (the closer you get to the end of the string, the less amplitude of vibration) so if you had pickups that were of equal output, the neck position would sound louder. Use a lower output neck pickup (or higher output bridge pickup) to compensate. Please correct me if I am barking up the wrong tree here. Quote Link to comment Share on other sites More sharing options...
Andyjr1515 Posted February 21, 2018 Share Posted February 21, 2018 I agree with @Bassalarky that usually, the bridge pickup would be higher resistance than the neck. Interestingly, looking at the Fender website, for their modern 'Vintage Noiseless' Jazz sets, the bridge is, indeed, the higher value. But the 'Pure Vintage '74' has the neck higher than the bridge. I get the impression from the decriptions on their marketing blurb, that the Pure Vintage is specifically trying to get warm low end and high mid range, whereas the Vintage Noiseless is trying to tame that mid end a bit. All of the Seymour Duncan sets seem to have the bridge higher so, unless you are pitching for a very specific effect, then I would have thought the resistances you quote are very much in the 'normal' ranges and should sound fine. Quote Link to comment Share on other sites More sharing options...
bakerster135 Posted February 21, 2018 Share Posted February 21, 2018 2 hours ago, Andyjr1515 said: I agree with @Bassalarky that usually, the bridge pickup would be higher resistance than the neck. Interestingly, looking at the Fender website, for their modern 'Vintage Noiseless' Jazz sets, the bridge is, indeed, the higher value. But the 'Pure Vintage '74' has the neck higher than the bridge. I get the impression from the decriptions on their marketing blurb, that the Pure Vintage is specifically trying to get warm low end and high mid range, whereas the Vintage Noiseless is trying to tame that mid end a bit. All of the Seymour Duncan sets seem to have the bridge higher so, unless you are pitching for a very specific effect, then I would have thought the resistances you quote are very much in the 'normal' ranges and should sound fine. Fender definitely have those Pure Vintage 74 values the wrong way round on their website, bridge is the higher value. Look at Nordy, Bare Knuckle, etc. 70s specs for comparison... Quote Link to comment Share on other sites More sharing options...
Andyjr1515 Posted February 21, 2018 Share Posted February 21, 2018 15 minutes ago, bakerster135 said: Fender definitely have those Pure Vintage 74 values the wrong way round on their website, bridge is the higher value. Look at Nordy, Bare Knuckle, etc. 70s specs for comparison... Well that certainly makes more sense.... Quote Link to comment Share on other sites More sharing options...
Geek99 Posted February 21, 2018 Author Share Posted February 21, 2018 Indeed it does make sense fess up time: these are stated to be from a geddy lee bass. I have no reason to disbelieve it Quote Link to comment Share on other sites More sharing options...
.jpg.7e18f76540598a8efc0e6ca9be453059.jpg)
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.