CameronJ Posted August 23, 2018 Share Posted August 23, 2018 Hey guys & gals, I’m starting work on a very special project and have a favour to ask of those of you who own an Aguilar Octamizer - could you measure the dimensions of the circuit board inside the pedal for me please? And, if possible, post a photo too? I’ll be forever indebted to you and if all goes to plan the end result will be incredibly cool! The actual measurements are much more important than the photo. Thanks in advance, Cameron Quote Link to comment Share on other sites More sharing options...
Quatschmacher Posted August 24, 2018 Share Posted August 24, 2018 19 hours ago, CameronJ said: Hey guys & gals, I’m starting work on a very special project and have a favour to ask of those of you who own an Aguilar Octamizer - could you measure the dimensions of the circuit board inside the pedal for me please? And, if possible, post a photo too? I’ll be forever indebted to you and if all goes to plan the end result will be incredibly cool! The actual measurements are much more important than the photo. Thanks in advance, Cameron Are you getting a custom build and sticking an Octamizer in it? Quote Link to comment Share on other sites More sharing options...
GisserD Posted August 24, 2018 Share Posted August 24, 2018 21 hours ago, CameronJ said: Hey guys & gals, I’m starting work on a very special project and have a favour to ask of those of you who own an Aguilar Octamizer - could you measure the dimensions of the circuit board inside the pedal for me please? And, if possible, post a photo too? I’ll be forever indebted to you and if all goes to plan the end result will be incredibly cool! The actual measurements are much more important than the photo. Thanks in advance, Cameron If nobody beats me too it I can do this for you tomorrow. Good excuse to get the board out of the cupboard storage Quote Link to comment Share on other sites More sharing options...
CameronJ Posted August 24, 2018 Author Share Posted August 24, 2018 2 hours ago, Quatschmacher said: Are you getting a custom build and sticking an Octamizer in it? I am indeed! 24 minutes ago, GisserD said: If nobody beats me too it I can do this for you tomorrow. Good excuse to get the board out of the cupboard storage Darren - you are a legend. Thanks so much. I owe you one! Quote Link to comment Share on other sites More sharing options...
GisserD Posted August 25, 2018 Share Posted August 25, 2018 16 hours ago, CameronJ said: I am indeed! Darren - you are a legend. Thanks so much. I owe you one! No worries mate. I can't wait to see how your new build turns out 😋 I tried to get some shots of the underside so you can gauge the boards thickness. There's 3 caps on the underside whish when you remove/move the pots and Jacks would be the thickest part of the board. Whick isn't very thick! Best of luck! 1 Quote Link to comment Share on other sites More sharing options...
CameronJ Posted August 25, 2018 Author Share Posted August 25, 2018 @GisserD, you are a legendary human. Quote Link to comment Share on other sites More sharing options...
CameronJ Posted August 25, 2018 Author Share Posted August 25, 2018 If I’m reading those measurements correctly, that’s 56mm wide by 78mm tall, yes? Quote Link to comment Share on other sites More sharing options...
GisserD Posted August 25, 2018 Share Posted August 25, 2018 I'd say 81 x 59 Rounding up to next mm in both cases Quote Link to comment Share on other sites More sharing options...
CameronJ Posted August 25, 2018 Author Share Posted August 25, 2018 Ah - I’ve read it all wrong! Thanks man Quote Link to comment Share on other sites More sharing options...
CameronJ Posted August 29, 2018 Author Share Posted August 29, 2018 (edited) @GisserD I don’t suppose you could measure the height of the board could you? As per email below, which for some reason went to my spam folder and I’ve only just seen... Edited August 29, 2018 by CameronJ Quote Link to comment Share on other sites More sharing options...
GisserD Posted August 30, 2018 Share Posted August 30, 2018 So the measurements are in.... Let's call it 30mm Although most of that is made up of the jack sockets, which surely won't be used?? And the pots, which could be mounted anywhere. Even the power connector won't be used as id expect it to be hard wired?? Removal of the aforementioned parts would make the board 16mm deep at the largest cap. But even those could be removed easily and "laid down" if it was to make the difference. Just my 2p tho. I'm sure the guys building it are way more competent than I at this sorta stuff. I can't wit to see how it goes!! 1 Quote Link to comment Share on other sites More sharing options...
CameronJ Posted August 30, 2018 Author Share Posted August 30, 2018 Once again, big thanks Darren - let’s see what they say! Quote Link to comment Share on other sites More sharing options...
CameronJ Posted August 30, 2018 Author Share Posted August 30, 2018 (edited) Andy’s (WingBass) response below: “We’d prefer not to do any desoldering and removal of components as that introduces the potential of destroying the circuit, and these are expensive. With the POG we don’t have to do any disassembly. That being said, I’m traveling on the West Coast and will return tomorrow so I can measure the depth of the cavity to determine if there is room. I will let you know for sure at that time.” Edited August 30, 2018 by CameronJ Quote Link to comment Share on other sites More sharing options...
CameronJ Posted August 30, 2018 Author Share Posted August 30, 2018 (edited) Makes sense I guess - I’d prefer it if no Octamizers were harmed in the making of this bass 😂 Edited August 30, 2018 by CameronJ Quote Link to comment Share on other sites More sharing options...
GisserD Posted August 30, 2018 Share Posted August 30, 2018 18 minutes ago, CameronJ said: Makes sense I guess - I’d prefer it if no Octamizers were harmed in the making of this bass 😂 Your going to be skinning it alive!!! 1 Quote Link to comment Share on other sites More sharing options...
CameronJ Posted September 4, 2018 Author Share Posted September 4, 2018 Looks like it’s going to be too deep for the control cavity - I’m seeing if they’d be willing to go down the desoldering route. I’ve even suggested buying a couple of used Octamizers for them to use as test units! Quote Link to comment Share on other sites More sharing options...
GisserD Posted September 4, 2018 Share Posted September 4, 2018 i had a close look before i reassembled mune and those surface mounted components are really easy to remove. any hobbiest with a soldering iron and a solder sucker could do it without destroying anything. or even risking anything for that matter!! i really hope you can find a way to make it work as everybody knows its the best octaver. anything else would just be settling!! Best of luck! Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.