fretmeister Posted April 8, 2019 Share Posted April 8, 2019 The AO pedal can do a pretty clean tone - I've used mine that way as a "warming up" always on type thing in the past. Don't know if the amp will do as little drive when the AO section is turned on though. Quote Link to comment Share on other sites More sharing options...
NancyJohnson Posted April 8, 2019 Share Posted April 8, 2019 I don't know I'm fully done with pedals just yet; while I'm sure this amp will do me fine for the time being, I'm still a whore for Tech21 and still have my dUg. I may swing for a Sansamp YYZ at some point for a bit more variety and to prove that I'm not done with the company just yet. While I haven't tried it yet, I'm assuming I can utilise the Darkglass poweramp side by just plugging the dUg into the return on the effects loop? 1 Quote Link to comment Share on other sites More sharing options...
Cuzzie Posted April 8, 2019 Author Share Posted April 8, 2019 Yeah - use the DP3x though there or up front on the amp. It will always give you something different and Tech21 are a very very good company. Doug Darkglass has a Tech21 dUg Ultrabass amp in his arsenal, so if he is not done with them, neither should you be! 2 Quote Link to comment Share on other sites More sharing options...
NancyJohnson Posted April 8, 2019 Share Posted April 8, 2019 7 hours ago, Cuzzie said: Yeah - use the DP3x though there or up front on the amp. It will always give you something different and Tech21 are a very very good company. Doug Darkglass has a Tech21 dUg Ultrabass amp in his arsenal, so if he is not done with them, neither should you be! The DP3X sounds peachy through the return. Definitely preferable than going in through the front. Bring on the YYZ stomp. 1 Quote Link to comment Share on other sites More sharing options...
Graemeross Posted April 14, 2019 Share Posted April 14, 2019 (edited) Love that amp @NancyJohnson. The connection options are much better than my MT900, which is pretty basic. Thanks for helping me to run in my cabs - they sounded great at the gig last night! For pedalboard options, I have a four cable setup with my pedalboard and it works well. Drive/distortion etc in the front, modulation/delay/reverb in the effects loop after the pre-amp. Edited April 14, 2019 by Graemeross 4 Quote Link to comment Share on other sites More sharing options...
ern500evo Posted April 15, 2019 Share Posted April 15, 2019 Has anyone pulled the trigger on the M900v2 yet? Quote Link to comment Share on other sites More sharing options...
Al Krow Posted July 27, 2019 Share Posted July 27, 2019 (edited) The one knob compression on the two new amps is described in the manual as: "controls the amount of dynamic compression added to the Microtubes Engine." That is a little ambiguous wording for me as it kinda implies that the compression is only available when the Microtubes Engine i.e. the dirt is engaged. But that would be a bit weird to not also be available just on the clean tone, particularly given that the Microtubes Engine can already be used "to add natural compression" so adding further compression to the drive would seem potentially less useful than to the clean. Looking at the circuit diag. it seems to me that the compression, like the gain, sits outside the Microtubes and can be used on just clean And that would also tie in with the markings on the front which indicate that the compression and gain are both not part of the Microtubes engine @NancyJohnson @Kieran30803 You gents able to confirm that I've understood this correctly i.e. compression can be used just with the clean tone? Edited July 27, 2019 by Al Krow Quote Link to comment Share on other sites More sharing options...
Al Krow Posted July 28, 2019 Share Posted July 28, 2019 @obbm - maybe trouble you to comment on the above, too, please while I have your attention! Quote Link to comment Share on other sites More sharing options...
obbm Posted July 28, 2019 Share Posted July 28, 2019 I'm not familiar with Darkglass equipment but from the diagram, text, and manual it would seem that with the Microtubes engine disengaged the clean signal goes straight to the compressor. 1 1 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.