Slappindabass Posted July 29, 2019 Share Posted July 29, 2019 So I received some cash for my Birthday and decided I would buy myself an nice ash p bass body but with jazz routings. I looked thenm up and for a one piece it was going to cost £230.00. A lot of money but if thats what they are. So I contacted the firm to see if i could see a picture of the blank they would use ....they wouldnt do that until I had paid. So I declined as I have seen some lovely ash and some awful looking ash. A little dissapointed I decided to see if I could build one myself for similar money. So I purchased off of sphock a Bandsaw, pillar drill, router. £95.00 total Tempate kit £55.00 Bit of ash 38.00 total Router bit 22.00 I have no woodworking skill at all...what i do have in abundance is ...stupidity that this is going to be any good....who knows! If the body turns out ok I am goi g to have a go at a neck. 12 Quote Link to comment Share on other sites More sharing options...
gjones Posted July 29, 2019 Share Posted July 29, 2019 Remember to count your fingers before cutting out the body and afterwards as well. If there's a discrepancy, call 999 right away. 😃 2 6 Quote Link to comment Share on other sites More sharing options...
Slappindabass Posted July 29, 2019 Author Share Posted July 29, 2019 🖕one 🤣🤣🤣 4 Quote Link to comment Share on other sites More sharing options...
paul_5 Posted July 30, 2019 Share Posted July 30, 2019 Measure twice, cut once. Quote Link to comment Share on other sites More sharing options...
durhamboy Posted July 30, 2019 Share Posted July 30, 2019 If you really are new to these tools, get some scrap wood and practice to get the feel of what the tools will do. If you haven't any clamps, invest in a few, you'll certainly need them when using tools like routers. Take your time and as gjones mentioned watch your fingers. 2 Quote Link to comment Share on other sites More sharing options...
Christine Posted July 30, 2019 Share Posted July 30, 2019 Wow, brave lad and that's just stacking that lot next to the VW Tips, get a good quality bandsaw blade, 3 or 4 TPI Hakansson, it will give you a better cut so you can gut closer to the line which means less routing, a big plus. Practice routing first and remember to go the right direction, going the wrong way can and frequently is disastrous for wood, router and body 1 Quote Link to comment Share on other sites More sharing options...
Slappindabass Posted July 30, 2019 Author Share Posted July 30, 2019 24 minutes ago, Christine said: Wow, brave lad and that's just stacking that lot next to the VW Tips, get a good quality bandsaw blade, 3 or 4 TPI Hakansson, it will give you a better cut so you can gut closer to the line which means less routing, a big plus. Practice routing first and remember to go the right direction, going the wrong way can and frequently is disastrous for wood, router and body Thanks. I intend using a table for the router trim around the body which i guess means I need to run the wood round in the opposite direction as the router is upside down. Re the bandsaw blade. Would love to change it but am worried about how hard it will be. Its running nice at the moment and wouldnt want to mess that up but would like to start wirh a nice fresh blade. I wii do a search and see if thete is a guide. Quote Link to comment Share on other sites More sharing options...
bertbass Posted July 30, 2019 Share Posted July 30, 2019 Band saw blades are easy to change. Here's one of many videos on how to do it. 2 Quote Link to comment Share on other sites More sharing options...
Christine Posted July 30, 2019 Share Posted July 30, 2019 3 hours ago, Slappindabass said: Thanks. I intend using a table for the router trim around the body which i guess means I need to run the wood round in the opposite direction as the router is upside down. Re the bandsaw blade. Would love to change it but am worried about how hard it will be. Its running nice at the moment and wouldnt want to mess that up but would like to start wirh a nice fresh blade. I wii do a search and see if thete is a guide. In a router table the wood moves across the front of the cutter from right to left, so from above clockwise. the cutter cuts into the wood not out of it, the shallower the cut the easier it will be, if you end up with a lot of wood to remove you'll need to take shallower cuts, now that can be dangerous as the wood will be feeding into the cutter unsupported and liable to grab and be thrown across the room into your shiny van. You can make this safer by fixing a 6mm pin about 6mm away from the cutter and use that as a rest to support the wood as you feed it in, makes it a doddle. Then you can easily control the depth of cut moving in wards on each pass until finally you're resting on the cutter bearing for the final cut 2 Quote Link to comment Share on other sites More sharing options...
Slappindabass Posted July 30, 2019 Author Share Posted July 30, 2019 82.1/2" (2095mm) x 1/4" x .025" Hakansson Silco 91 82 Tooth Pitch: 4 tpi (1) 82.1/2" (2095mm) x 1/2" x .025" Hakansson Silco £9.15 £9.15 Tooth Pitch: 3 tpi Just ordered these. 1 Quote Link to comment Share on other sites More sharing options...
Christine Posted July 30, 2019 Share Posted July 30, 2019 You'll not regret it, they are fantastic blades, streets ahead of anything else Quote Link to comment Share on other sites More sharing options...
Slappindabass Posted August 1, 2019 Author Share Posted August 1, 2019 The blades arrived so I thought I would have a go at changing it. I think I got there in the end. It just so happened a bit of cheap(has imperfections) black Limba turned up as well. So thought why not!😁👍 This is my test bed. Everytging I do will be done on this before I touch my Ash body. Everyone said get close to the lines. I think I have achieved that. Maybe a tad too close in places. But .....it still lools like a guitar, I still have my fingers so win win. 2 Quote Link to comment Share on other sites More sharing options...
Slappindabass Posted August 1, 2019 Author Share Posted August 1, 2019 Ps Christine the Blades are great. Thanks cut that with a 6mm one. 1 Quote Link to comment Share on other sites More sharing options...
Christine Posted August 1, 2019 Share Posted August 1, 2019 I used to cut 10" x 1/8 veneers in Rosewood, Satinwood and Macassar Ebony with a 1/2" 3TPI Hakansson blade, can't say more than that about them 1 Quote Link to comment Share on other sites More sharing options...
Slappindabass Posted August 2, 2019 Author Share Posted August 2, 2019 Can someone explain how this is possible?!?!? As younlook at it I will be feeding from right to left. Quote Link to comment Share on other sites More sharing options...
Jimothey Posted August 2, 2019 Share Posted August 2, 2019 Your arrows are going the wrong way you never go with the direction of the cutter you always go against it, are you using a template to trim the body or are you trying to do it freehand? I don’t understand what you mean by the uphill/downhill part? Quote Link to comment Share on other sites More sharing options...
Slappindabass Posted August 2, 2019 Author Share Posted August 2, 2019 (edited) Its in a table. I dont understand the uphill down hill part either but, apparently if you start at the green stop at the red it reduces tear out. Feeding right to left would be against the rotation so its correct in that. The arrows are not for feeding direction. Just wbere to start and stop. Edited August 2, 2019 by Slappindabass Quote Link to comment Share on other sites More sharing options...
Christine Posted August 2, 2019 Share Posted August 2, 2019 The wood will move across the cutter as is in a from the right to the left, so the cutter advances through the wood in the direction of the arrows. If the wood moves in the direction of the arrows it will become airborne faster than you could ever know. Uphill, downhill is purely cutting with or against the grain direction so downhill (with the grain) you'll get a smoother cut than uphill (against the grain) so uphill you need shallower cuts Along with @Jimothey you are using a template not freehand? Quote Link to comment Share on other sites More sharing options...
Slappindabass Posted August 2, 2019 Author Share Posted August 2, 2019 To be fair how close i am with the bandsaw i think it is going to be ok. Yes I shall be using a template. Also purchased a 4 flute bit today which are quite well regarded. Quote Link to comment Share on other sites More sharing options...
Slappindabass Posted August 2, 2019 Author Share Posted August 2, 2019 So as i suspected it is not entirely possible to follow that map. Quote Link to comment Share on other sites More sharing options...
Jimothey Posted August 2, 2019 Share Posted August 2, 2019 5 minutes ago, Slappindabass said: To be fair how close i am with the bandsaw i think it is going to be ok. Yes I shall be using a template. Also purchased a 4 flute bit today which are quite well regarded. If your using a template as @Christine said on a previous thread use a guide pin to control the amount you are removing in one pass if it’s more than about 3mm if it’s less than that you could probably remove it in one pass but don’t try and do it too quickly as you run the risk of tear out but don’t do it too slowly or you run the risk of burning the wood which can be hard to sand off?? Whats the length of your cutter is it less than the depth of the body if so you will have to raise the cutter once you’ve done the first pass then go round it again then raise it again etc till your above the top of your body?? Quote Link to comment Share on other sites More sharing options...
Christine Posted August 2, 2019 Share Posted August 2, 2019 15 minutes ago, Slappindabass said: Also purchased a 4 flute bit today which are quite well regarded. as that one of the Radian tools cutters? I have one and I think it's the best cutter I've owned for template following 1 Quote Link to comment Share on other sites More sharing options...
Slappindabass Posted August 2, 2019 Author Share Posted August 2, 2019 (edited) It is👍 Edited August 2, 2019 by Slappindabass Quote Link to comment Share on other sites More sharing options...
Slappindabass Posted August 2, 2019 Author Share Posted August 2, 2019 36 minutes ago, Christine said: as that one of the Radian tools cutters? I have one and I think it's the best cutter I've owned for template following It is.👍😁 1 Quote Link to comment Share on other sites More sharing options...
Slappindabass Posted August 2, 2019 Author Share Posted August 2, 2019 Double post! Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.