JBoman Posted November 3, 2019 Share Posted November 3, 2019 (edited) We have in our neighbourhood these shared spaces for hobbies, a gym, garage, etc things that typically you do not have in multi-family housing. For a small fee, you get access. One of these spaces is for handcrafts, mainly to do with wood. I had no specific idea what I'm going to do there, just enrolled out of curiosity. I've been somewhat good with my hands all my life, so I thought I'll eventually come up with interesting projects. Some weeks go by and I start to notice these piles of misc wood pieces. Mostly scrap wood, knotty pine, the usual stuff. Then I notice this interesting piece of some hardwood with the words "free to use" written on it. I ask around and seems like no one is missing it so I just take it and immediatelty notice some potential for a bass guitar body. I measure, look at the grains and start to feel all warm and giddly inside. Yes yes yessssss.. It barely has enough dimensions for a body blank, but it's doable. I cut it in two pieces and found this nice alignment with the grains to get a kind of bookmatched vibe going on. At that time (it was like one year ago) I was super psyched about MM basses, so I then order a Stingray template set. While I wait for the templates to arrive, I use my SUB to get some rough idea of the body area and start to work on the glue joint. I clean the glue joint with some sanding blocks and razor blades, to get it to fit and not to have any gaps. Time for some Tite-Bond. The templates arrive, I make "backups" since the template material is kinda weak feeling. I use the "backups" to start the quality time with a router. After some passes with the straight router bit and a curved bit for the edges. Quite some time passes between the fotos, wasn't really thinking about documentation. This block is HEAVY, therefore I decided to make it ligher by making a generous space for all kinds of potential electronics setups. Also decided to go without the plate in the front and do everything from behind. The straight line was done using a guide, the rest is basically freehand. I also made a test cover from some other wood that was similar, but it actually came out so nice that I'll actually use it. I'm thinking of doing the attachment with some magnets, so that I can replace for example a battery without screws. Oh, also worked on the belly cut and the cutaway in the front. So here we are now, from this point forwards it gets expensive. I have always wanted to have one bass with a Status graphite neck, this most probably will be that one. Also, I'm really going back & forth with finishing, hardware color, etc overall look & feel. Suggestions welcome This list looks most probable at the moment: - Status neck - Chrome machine heads - Black bridge - Black pickguard or see-through or wood with hard finish - Electronics cover black with grains a bit visible - Soapbar style pickup (no magnets visible) - The body will definetly be done so that grains are clearly visible, looks really nice Edited November 3, 2019 by Jbomam 16 1 Quote Link to comment Share on other sites More sharing options...
JBoman Posted November 3, 2019 Author Share Posted November 3, 2019 Offtopic: new here and I just noticed that I made a typo in my profile name, is it possible to change it? Cannot find the option.... Quote Link to comment Share on other sites More sharing options...
TheGreek Posted November 3, 2019 Share Posted November 3, 2019 PM one of the Mods - they can do it for you... Welcome to the Forum... 2 Quote Link to comment Share on other sites More sharing options...
JBoman Posted November 4, 2019 Author Share Posted November 4, 2019 Thanks for the advice. Some inspirational picks from the web... Turns out that finding some hardware parts has proved to be difficult. I would like to have properly chromed machine heads, not that nickel plated crap. Also, a 6-bolt neck plate with proper dimensions (and again, properly chromed) is nowhere to be found... Quote Link to comment Share on other sites More sharing options...
itu Posted November 4, 2019 Share Posted November 4, 2019 Welcome sir, I think that changing the last letter (you don't have to ask, how I knew), you should ask @ped If you are in need of a neck, there may be a chance to discuss about one, the tinted one. Do not make screw holes for the neck, yet... Quote Link to comment Share on other sites More sharing options...
itu Posted November 4, 2019 Share Posted November 4, 2019 By the way, there is one EMG in my closet, too... Quote Link to comment Share on other sites More sharing options...
SpondonBassed Posted November 4, 2019 Share Posted November 4, 2019 Welcome J. Nice build. 1 Quote Link to comment Share on other sites More sharing options...
JBoman Posted November 4, 2019 Author Share Posted November 4, 2019 3 hours ago, itu said: Welcome sir, I think that changing the last letter (you don't have to ask, how I knew), you should ask @ped If you are in need of a neck, there may be a chance to discuss about one, the tinted one. Do not make screw holes for the neck, yet... Neck pocket is not yet even routed and will stay that way until I have a neck that I can compare to my template Quote Link to comment Share on other sites More sharing options...
durhamboy Posted November 5, 2019 Share Posted November 5, 2019 Nice looking piece of wood you've got there, some variety of ash by the look. Nice work so far too. Quote Link to comment Share on other sites More sharing options...
JBoman Posted November 6, 2019 Author Share Posted November 6, 2019 18 hours ago, durhamboy said: Nice looking piece of wood you've got there, some variety of ash by the look. Nice work so far too. Ash, or someone suspected also oak. Anyway, it's like a brick. I expect the bass to sound... big. 2 Quote Link to comment Share on other sites More sharing options...
JBoman Posted July 3, 2020 Author Share Posted July 3, 2020 (edited) Finally some updates. I decided to put this on the scale and landed on a whopping 3,5kg. Yikes. I then decided to put this on a diet. I also noticed that thikness was also a bit too much, about 42mm. So with that I mind, I made this kind of a routing jig / contraption for shaving off layers from top and bottom (well, front and back actually...). I know that Stingrays are officially about 40mm thick, but for the sake of weight control and also curiosity, I went down to 39mm. I like routing, it's meditative like painting. Preparations just take 80% of the time Of course after this I also had to make that electronics cover thinner but good thing it was thick to begin with. Also, edges had to be re-done, no biggie. I'm hoping that the neck route will get rid of some extra weight and I also have a special feature in mind, more about that later Edited July 3, 2020 by JBoman 9 Quote Link to comment Share on other sites More sharing options...
Grangur Posted July 8, 2020 Share Posted July 8, 2020 On 06/11/2019 at 15:04, JBoman said: Ash, or someone suspected also oak. Anyway, it's like a brick. I expect the bass to sound... big. It's not likely to be oak. Oak will normally have medullary rays in it. Thease are the light-coloured flecks that you see in oak furniture. It would make it seriously heavy for a bass body though. 1 Quote Link to comment Share on other sites More sharing options...
JBoman Posted July 11, 2020 Author Share Posted July 11, 2020 @Grangur, thanks for the info. One thing I that might have gone wrong with this project is the templates that I ordered. They appeared to be very good so I just went with them without any worry in mind. Then just recently, I took the time to compare the templates more closely with my US made S.U.B. The body size does not match, the overall length is about 1cm more on the template. Also, pickguard size is not the same, the template is slightly larger than the pickguard on my S.U.B. It's like the whole template is slighty "scaled up" or something. Of course, since this is a custom project I can probably deal with this. I was going to make a pickguard from a blank anyway, but it's a bummer that stock pickguards are not going to be compatible... Or, could it be that Stingray body dimensions have changed over the years and the template and my S.U.B are based on a slighty different design? Vintage versus modern, for example? 1 Quote Link to comment Share on other sites More sharing options...
songofthewind Posted July 11, 2020 Share Posted July 11, 2020 9 minutes ago, JBoman said: @Grangur, thanks for the info. One thing I that might have gone wrong with this project is the templates that I ordered. They appeared to be very good so I just went with them without any worry in mind. Then just recently, I took the time to compare the templates more closely with my US made S.U.B. The body size does not match, the overall length is about 1cm more on the template. Also, pickguard size is not the same, the template is slightly larger than the pickguard on my S.U.B. It's like the whole template is slighty "scaled up" or something. Of course, since this is a custom project I can probably deal with this. I was going to make a pickguard from a blank anyway, but it's a bummer that stock pickguards are not going to be compatible... Or, could it be that Stingray body dimensions have changed over the years and the template and my S.U.B are based on a slighty different design? Vintage versus modern, for example? It’s likely to do with copyright infringement. Sterling Ball is notoriously litigious. This is a nice project. I’m doing a similar one, and it’s interesting to compare and contrast with yours. My body is some kind of mahogany, and I’m waiting for a maple cap to arrive. I may chamber the body. Quote Link to comment Share on other sites More sharing options...
JBoman Posted July 11, 2020 Author Share Posted July 11, 2020 1 minute ago, songofthewind said: It’s likely to do with copyright infringement. Sterling Ball is notoriously litigious. Should have known it..... well, I always have the option to trace out my SUB and make a second one if this starts to irritate me Only cost so far has been my precious time And this project actually has a couple of routing mishaps that I tried to cover up with various degree of success. Also I bet a 2nd attempt with a new block of wood would go much much faster with all the experience and "gotchas" I gained from this one. 1 Quote Link to comment Share on other sites More sharing options...
songofthewind Posted July 11, 2020 Share Posted July 11, 2020 Maybe a lighter piece of wood, as part of a new project, would be the way to go. Or go with a cap, and really dig out the inside of the existing body! Quote Link to comment Share on other sites More sharing options...
JBoman Posted July 11, 2020 Author Share Posted July 11, 2020 29 minutes ago, songofthewind said: Maybe a lighter piece of wood, as part of a new project, would be the way to go. Or go with a cap, and really dig out the inside of the existing body! Nah, the top looks way too nice to cover it. Maybe something to the backside... hmmm Quote Link to comment Share on other sites More sharing options...
GarethFlatlands Posted July 12, 2020 Share Posted July 12, 2020 19 hours ago, JBoman said: Nah, the top looks way too nice to cover it. Maybe something to the backside... hmmm Maybe route out some chambers on the back, cover them in the same way as your electronics cavity and put a few tasteful f-holes on the front? It's what I'm considering for my build if the tulipwood body is still crazy heavy after it's been thicknessed and shaped. Quote Link to comment Share on other sites More sharing options...
Fishman Posted July 14, 2020 Share Posted July 14, 2020 I have this template too – bought from The Netherlands – you're right, it's out on every measurement Quote Link to comment Share on other sites More sharing options...
JBoman Posted July 15, 2020 Author Share Posted July 15, 2020 12 hours ago, Fishman said: I have this template too – bought from The Netherlands – you're right, it's out on every measurement It seems we have the same guy to blame Some parts arrive. String tree, pickguard blank and strap buttons from a local shop. Neck plate courtesy of our litigating friends in China X) Some more measurement considerations: neck plate holes do not line up. Not really a suprise at this point I would say. It's not an real issue if I do not want the neck to be interchangeable with my SUB (which I might find interesting at some point...). So, either I drill with these holes or mabey use those that have the individual bushings... (example image attached) 2 Quote Link to comment Share on other sites More sharing options...
Fishman Posted July 16, 2020 Share Posted July 16, 2020 another neck plate supplier if you need it: https://tlcguitargoods.com/en/neck-plate-bass-6-hole-music-man-style-stainless-steel.html Quote Link to comment Share on other sites More sharing options...
Fishman Posted July 16, 2020 Share Posted July 16, 2020 (edited) and another – I got mine from here: https://www.facebook.com/TONE5PARTS/ Edited July 16, 2020 by Fishman 2 Quote Link to comment Share on other sites More sharing options...
SpondonBassed Posted July 16, 2020 Share Posted July 16, 2020 1 hour ago, Fishman said: and another – I got mine from here: Didn't they sell a full set of screws with it then? 1 Quote Link to comment Share on other sites More sharing options...
Pea Turgh Posted July 16, 2020 Share Posted July 16, 2020 The middle two are tone ports. 2 Quote Link to comment Share on other sites More sharing options...
JBoman Posted July 17, 2020 Author Share Posted July 17, 2020 On 16/07/2020 at 15:57, SpondonBassed said: Didn't they sell a full set of screws with it then? Found these also in ebay (Tone5) but: Quote Hi, Sorry my friend, we have to cancel your order. Because Postal services to certain destinations suspended or delay. Can’t not shipping to Finland now. Looking forward to dealing with you in the future. 1 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.