andyowenuk Posted January 25, 2020 Share Posted January 25, 2020 (edited) Hi, Has anyone else had an issue after upgrading the firmware on their future impact pedal where the tuner no longer functions correctly? Works on 2.02 Firmware versions 2.22 and 3 tune flat. If you revert back to 2.02 it works again 🤷♂️. Very strange. Thanks Andy Edited January 25, 2020 by andyowenuk Quote Link to comment Share on other sites More sharing options...
MuddBass Posted January 25, 2020 Share Posted January 25, 2020 Did not know it had a tuner! Quote Link to comment Share on other sites More sharing options...
andyowenuk Posted January 25, 2020 Author Share Posted January 25, 2020 (edited) 2 minutes ago, MuddBass said: Did not know it had a tuner! It's not the best, was an addition from 2.02 onwards. You press an hold the on/off button to access Edited January 25, 2020 by andyowenuk 1 Quote Link to comment Share on other sites More sharing options...
Al Krow Posted January 25, 2020 Share Posted January 25, 2020 I had the very same issue. @Quatschmacher kindly put me straight and all working fine now and the new tuner is actually much improved. There's a lengthy bit of hand holding on one of the threads somewhere... 1 Quote Link to comment Share on other sites More sharing options...
andyowenuk Posted January 26, 2020 Author Share Posted January 26, 2020 12 hours ago, Al Krow said: I had the very same issue. @Quatschmacher kindly put me straight and all working fine now and the new tuner is actually much improved. There's a lengthy bit of hand holding on one of the threads somewhere... Do you have a link to the thread? I've searched through and can't find anything as yet 🙂 Quote Link to comment Share on other sites More sharing options...
Al Krow Posted January 26, 2020 Share Posted January 26, 2020 Ah yes, it's not in an obvious place at all! It's actually on this thread - discussion starts on Nov 15th 2019 when I start by moaning that "I've not found the FI tuner to be that good / accurate"... sound familiar?!😁 You have to reset the FI to 440Hz after upgrading the software version. It's set out in the manual on the boot menu or FAQs. 2 Quote Link to comment Share on other sites More sharing options...
Quatschmacher Posted January 26, 2020 Share Posted January 26, 2020 (edited) @andyowenuk I’ve PMd you. Basically you need to either perform a “reset all” or set the “tune base” manually. Both of these are done via the boot menu. Read the section called “editing the configuration parameters” on pages 13-14 of the manual. Click the link below: Edited January 26, 2020 by Quatschmacher 1 Quote Link to comment Share on other sites More sharing options...
Quatschmacher Posted January 26, 2020 Share Posted January 26, 2020 I heartily recommend reading the manual as there’s loads of good stuff in there and there are probably features you didn’t even know existed. 1 Quote Link to comment Share on other sites More sharing options...
andyowenuk Posted January 26, 2020 Author Share Posted January 26, 2020 3 hours ago, Quatschmacher said: I heartily recommend reading the manual as there’s loads of good stuff in there and there are probably features you didn’t even know existed. Thanks for the link to the detailed manual, all working correctly now! 🙂👍👍 1 Quote Link to comment Share on other sites More sharing options...
Quatschmacher Posted January 26, 2020 Share Posted January 26, 2020 5 minutes ago, andyowenuk said: Thanks for the link to the detailed manual, all working correctly now! 🙂👍👍 Glad to hear it. Do check out the examples in the manual too; I wrote a whole section on using the FI to replace single effects stomp boxes and a section on how to create your own sounds from scratch. 2 Quote Link to comment Share on other sites More sharing options...
andyowenuk Posted January 26, 2020 Author Share Posted January 26, 2020 Will check it out Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.