Radchenko Posted October 6, 2020 Share Posted October 6, 2020 Hello, A luthier made me this nut. Do you think is ok please?. Is neccesary the lines be straight? Thank you. Quote Link to comment Share on other sites More sharing options...
PaulThePlug Posted October 6, 2020 Share Posted October 6, 2020 String slots arn't straight, and the nut looks a little wide... Hope they didn't charge you! Quote Link to comment Share on other sites More sharing options...
Thunderbird Posted October 6, 2020 Share Posted October 6, 2020 (edited) That's terrible I don't think a proper luthier would pass that off I'd take it back mate it looks like it's been done with a dremel as the material is marked and looks rough on the edges almost like melted but it is hard to tell just from the picture Edited October 6, 2020 by Thunderbird Quote Link to comment Share on other sites More sharing options...
BreadBin Posted October 6, 2020 Share Posted October 6, 2020 12 minutes ago, PaulThePlug said: String slots arn't straight, and the nut looks a little wide... Hope they didn't charge you! Bang on, a very poor effort frankly. Quote Link to comment Share on other sites More sharing options...
Reggaebass Posted October 6, 2020 Share Posted October 6, 2020 Ola Radchenko, it looks untidy to me, here’s my Sandberg for comparison 🙂 Quote Link to comment Share on other sites More sharing options...
ezbass Posted October 6, 2020 Share Posted October 6, 2020 1 hour ago, Radchenko said: Hello, A luthier made me this nut. Do you think is ok please?. Is neccesary the lines be straight? Thank you. That’s a nasty looking bit of work. Your strings are going to catch when tuning, especially on the G. Quote Link to comment Share on other sites More sharing options...
Radchenko Posted October 6, 2020 Author Share Posted October 6, 2020 (edited) 14 minutes ago, ezbass said: That’s a nasty looking bit of work. Your strings are going to catch when tuning, especially on the G. Thank you, Sorry, what is catch?. Edited October 6, 2020 by Radchenko Quote Link to comment Share on other sites More sharing options...
A.G.E.N.T.E. Posted October 6, 2020 Share Posted October 6, 2020 That looks a bit of (cheap) plastic, and the work dosen`t look very professional. I know the image is a bit magnified but.. i don`t know if you can call that señor a luthier. I think that depends on the context. Was this charged as low cost and fast solution or as premium service? Nonetheless, that might be a perfectly funcional nut. Quote Link to comment Share on other sites More sharing options...
PaulThePlug Posted October 6, 2020 Share Posted October 6, 2020 Catch... Stick - not slide when tuning 1 Quote Link to comment Share on other sites More sharing options...
Radchenko Posted October 6, 2020 Author Share Posted October 6, 2020 48 minutes ago, A.G.E.N.T.E. said: That looks a bit of (cheap) plastic, and the work dosen`t look very professional. I know the image is a bit magnified but.. i don`t know if you can call that señor a luthier. I think that depends on the context. Was this charged as low cost and fast solution or as premium service? Nonetheless, that might be a perfectly funcional nut. Thank you, Actually is carbono 😞 Quote Link to comment Share on other sites More sharing options...
Beedster Posted October 6, 2020 Share Posted October 6, 2020 Awful, slots not straight, blank too wide for neck so all slots shifted towards treble side with nut overhanging, G and D slots close to same width. Quote Link to comment Share on other sites More sharing options...
ezbass Posted October 6, 2020 Share Posted October 6, 2020 2 hours ago, Radchenko said: Thank you, Sorry, what is catch?. The windings will stick on the angled slots making tuning troublesome. 1 Quote Link to comment Share on other sites More sharing options...
robertg43 Posted October 7, 2020 Share Posted October 7, 2020 I wouldnt put my name to it Quote Link to comment Share on other sites More sharing options...
Beedster Posted October 7, 2020 Share Posted October 7, 2020 1 hour ago, robertg43 said: I wouldnt put my name to it Unless your name was Mr Rubbish Nut 2 4 Quote Link to comment Share on other sites More sharing options...
Drax Posted October 11, 2020 Share Posted October 11, 2020 @Radchenko you don't have much luck with custom builds do you mate? Quote Link to comment Share on other sites More sharing options...
Radchenko Posted October 11, 2020 Author Share Posted October 11, 2020 2 hours ago, Drax said: @Radchenko you don't have much luck with custom builds do you mate? Trying to fix Adrian fails, still on It. Thank you. Quote Link to comment Share on other sites More sharing options...
yorks5stringer Posted October 17, 2020 Share Posted October 17, 2020 On 11/10/2020 at 14:48, Radchenko said: Trying to fix Adrian fails, still on It. Thank you. Is this what was fitted direct from 'he who cannot be named'? If so, that is very poor but the good thing is it's very easy to fix ( not that you should have to ) Quote Link to comment Share on other sites More sharing options...
.jpg.7e18f76540598a8efc0e6ca9be453059.jpg)
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.