violetelectric Posted October 15, 2020 Share Posted October 15, 2020 So basically I bought this bass last month or so off gumtree. It's a 96' 50 year anniversary squier p bass. Had no problems with it at first but over the last couple of weeks it's been doing this thing where the volume - and even a little bit of gain - dip in volume. (It makes the sound very low in volume and also sounds very tone dead, like the pickups have 0 life). So everytime it does this I give the input lead to my bass a wiggle and it'll click in an out of being at regular volume and super quiet until it luckily sits right and I can continue recording again. It's becoming so infuriating and making my recording process a living hell. Also I must add the the input jack sits very loosely inside the guitar. I feel that this is likely the cause of the issue but as someone who's technical knowledge for guitars extends as far being able to change non-bass strings, I have no idea where to start. I appreciate any help greatly Quote Link to comment Share on other sites More sharing options...
BassBunny Posted October 15, 2020 Share Posted October 15, 2020 It looks like the simple answer is to change the jack, but if you aren't that savvy why not check the list of "basschatters who are prepared to help" and see if there is anyone near you who could do it. Personally I would change the pots as well as having had a Squier CV before, they aren't that good. Suggestion 3 is contact @KiOgon for one of his solder free looms. If you can handle a screwdriver, these are a doddle to fit. If you happen to be in the Manchester area, I'd be happy to have a look. Quote Link to comment Share on other sites More sharing options...
violetelectric Posted October 15, 2020 Author Share Posted October 15, 2020 @BassBunny thanks for the suggestions. I am going to move over there and do that now. Out of curiosity what do you mean when you say replace the jack? Unfortunately not I'm up in Edinburgh, thanks though Quote Link to comment Share on other sites More sharing options...
blisters on my fingers Posted October 16, 2020 Share Posted October 16, 2020 (edited) This sounds like a problem that everybody that owns an electric bass/guitar /mandolin! etc. will eventually encounter. The typical output jack is an ancient design that works very well until it err... starts to fail !! As a first step to fix your problem and before you start changing any components I would try this ... Remove all the screws on the outer edge of the scratchplate (not the pickup screws).. Loosen the strings or even take them off the tuners, be careful if you want to put the same strings back on Carefully lift up the scratchplate Now look at the output jack The long springy part with a "V" shape should make good contact with the tip of the jackplug when plugged in Try bending that springy part of the output jack in towards the centre of the output jack so it has a stronger physical contact with your guitar lead. Try inserting the lead and see if it now has a more positive connection That will probably cure it Might be worth cleaning the tip of the V shaped bit with some sandpaper or something similar to remove any corrosion Edited October 16, 2020 by blisters on my fingers Quote Link to comment Share on other sites More sharing options...
violetelectric Posted October 16, 2020 Author Share Posted October 16, 2020 7 hours ago, blisters on my fingers said: This sounds like a problem that everybody that owns an electric bass/guitar /mandolin! etc. will eventually encounter. The typical output jack is an ancient design that works very well until it err... starts to fail !! As a first step to fix your problem and before you start changing any components I would try this ... Remove all the screws on the outer edge of the scratchplate (not the pickup screws).. Loosen the strings or even take them off the tuners, be careful if you want to put the same strings back on Carefully lift up the scratchplate Now look at the output jack The long springy part with a "V" shape should make good contact with the tip of the jackplug when plugged in Try bending that springy part of the output jack in towards the centre of the output jack so it has a stronger physical contact with your guitar lead. Try inserting the lead and see if it now has a more positive connection That will probably cure it Might be worth cleaning the tip of the V shaped bit with some sandpaper or something similar to remove any corrosion thank you very much i shall try this today and get back to you here :) Quote Link to comment Share on other sites More sharing options...
3below Posted October 16, 2020 Share Posted October 16, 2020 (edited) Perfectly described by @blisters on my fingers This image might also help . When you put the scratchplate back on, fit all the screws loosely then give them all the final tightening. Makes aligning the holes easier. Edited October 16, 2020 by 3below 1 Quote Link to comment Share on other sites More sharing options...
stevel Posted October 16, 2020 Share Posted October 16, 2020 OP - you say the input jack sits very loosely inside the guitar - it's only held on with a thin nut - if this gets too loose it might just be that the output jack is shorting out on the inside, possibly against the control cavity (if it is conductive) which would result in the symptoms you describe. Worth trying just to tighten up the nut. If you're not sure which bit I'm on about, post us a photo of your output jack so we can point it out. 1 Quote Link to comment Share on other sites More sharing options...
mcnach Posted October 17, 2020 Share Posted October 17, 2020 If you can't get this fixed yourself, feel free to PM me (I'm in Edinburgh) and I could look at this for you. 1 1 Quote Link to comment Share on other sites More sharing options...
Jean-Luc Pickguard Posted October 17, 2020 Share Posted October 17, 2020 If you replace the socket, or get someone to replace it, make sure you get a mono switchcraft jack socket. Standard cheapo ones lose their springiness over time but switchcraft ones are much sturdier. 2 1 Quote Link to comment Share on other sites More sharing options...
violetelectric Posted October 17, 2020 Author Share Posted October 17, 2020 4 hours ago, Jean-Luc Pickguard said: If you replace the socket, or get someone to replace it, make sure you get a mono switchcraft jack socket. Standard cheapo ones lose their springiness over time but switchcraft ones are much sturdier. https://www.stewmac.com/kits-and-projects/electronic-kits/wiring-kits/premium-wiring-kit-for-p-bass.html?utm_source=google&utm_medium=shopping&utm_campaign=2020-10-gp&pref_currency=P&shipcalc=UK&gclid=CjwKCAjwrKr8BRB_EiwA7eFapvADpG_OatobK_2TEQGbR3ho-7lHLF0sSeGAx-i5v8r0IAUXhMFMIBoCGT4QAvD_BwE this one has the switchcraft jack socket? is this correct Quote Link to comment Share on other sites More sharing options...
Jean-Luc Pickguard Posted October 17, 2020 Share Posted October 17, 2020 Yes thats the one. Quote Link to comment Share on other sites More sharing options...
BassBunny Posted October 17, 2020 Share Posted October 17, 2020 If you're going for a kit get @KiOgon to make you one. He only uses quality components and it's a no solder solution. 2 1 Quote Link to comment Share on other sites More sharing options...
MoonBassAlpha Posted October 19, 2020 Share Posted October 19, 2020 I've found that on guitars that haven't been used for ages that it's often NOT just the tip contact that's bad, it's the contact to the ground of the Jack that's poor. Try roughing that up with fine wet n dry paper wrapped round a small screwdriver. Don't forget to clean it thoroughly afterwards. 2 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.