Jump to content
Why become a member? ×

The tone pot on my vintage precision isn’t very effective.


ossyrocks
 Share

Recommended Posts

 I’m the proud owner of a ‘73 Precision. I’ve only had it a couple of days, but yesterday I spent time with it through two different amps, my little Rumble 15 in the lounge, and my Markbass LM. 
 

I feel that the tone pot doesn’t have the sweep that it should have. It does work, but even backing it off completely doesn’t roll off the highs as I feel it should. The cheap Squire I have has a lot more tonal sweep than this does. I want to be able to really roll off the highs if I need to, and at the moment I’m using the bass with the tone pot rolled all the way back, and it’s just getting there.

 

As I am unfamiliar with vintage Precisions, is this normal, or should I be taking a look at the pot and the tone capacitor? My feeling is that the cap might be way out by now. I can’t see the pot being at fault, it’s silent in operation, and I’ve got older pots in older equipment and they rarely fail.

 

Any opinions and experience welcome.

 

Cheers,

Rob

 

Edited by ossyrocks
Link to comment
Share on other sites

55 minutes ago, ossyrocks said:

250K Audio CTS pots, dated 1973 with a .05uf capacitor/ Looks ok, and original.

 

I might just reflow the solder to start with and see if that makes a difference.

 

 

1973-fender-precision-bass-28.jpg

Yes maybe start with that and if that doesn't work then maybe try a higher value capacitor which should roll off more highs, when I had a pj Mustang the tone went from bright when on full to full on dub reggae with the tone rolled off so maybe try and find out what capacitor value the pj Mustang basses use

Edited by shoulderpet
Link to comment
Share on other sites

5 hours ago, ossyrocks said:

250K Audio CTS pots, dated 1973 with a .05uf capacitor/ Looks ok, and original.

 

The only thing that doesn't look original is the fat white earth wire from the jack to vol pot. Looks like this has been added later. See pic below of original wiring on another '73. Soldering on the pot case is much tidier and the earth tag on the jack is unconnected (common with this era).  One end of the tone cap goes to earth on the vol pot case so check that it's making a good connection. I'd be tempted to resolder that anyway and maybe dispense with the added earth wire. Or replace it with a black wire of the same gauge as the original wiring just to make it a bit tidier and consistent with black=earth.

 

565467616_1973Pwiring.jpg.dbe010fe86c39a67856d0143e3fe70d1.jpg

Edited by ikay
Link to comment
Share on other sites

3 hours ago, ikay said:

 

The only thing that doesn't look original is the fat white earth wire from the jack to vol pot. Looks like this has been added later. See pic below of original wiring on another '73. Soldering on the pot case is much tidier and the earth tag on the jack is unconnected (common with this era).  One end of the tone cap goes to earth on the vol pot case so check that it's making a good connection. I'd be tempted to resolder that anyway and maybe dispense with the added earth wire. Or replace it with a black wire of the same gauge as the original wiring just to make it a bit tidier and consistent with black=earth.

 

565467616_1973Pwiring.jpg.dbe010fe86c39a67856d0143e3fe70d1.jpg

That's a great point, if the ground wire is not making good contact then that could explain the lack in tonal variation when the highs are not being bled to ground

Link to comment
Share on other sites

@ikayThat’s really useful thanks. I can see why that earth wire was added, and I’ll probably wire another in, but better. Relying on the shielding under the guard to hold the earth to the jack isn’t the greatest, but there are probably thousands of P basses out there with exactly that.

Link to comment
Share on other sites

I’ve had a look at it today. It was immediately apparent what the issue was. One leg of the cap was touching the wiper of the tone pot.  I just gently moved the cap a bit and moved the leg away from the pot lugs. I did re-do that ground on the back of the pot, and I shortened and tidied up that added ground to the jack.

 

All back together now with a new set of flats on it. Everything is as it should be now.

 

Thanks for the input chaps.

 

Rob

  • Like 5
  • Thanks 1
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

 Share

  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...