lidl e Posted May 16, 2023 Share Posted May 16, 2023 What product in amazon is good for that? Just those lttle yellow sticks? Or is there a creme or paste? Quote Link to comment Share on other sites More sharing options...
itu Posted May 16, 2023 Share Posted May 16, 2023 Which screws? Machine, wood? For machine screws nearly any oil is better than no oil at all. The only exception is if you need thread lock (nail lacquer for soft, thread lock for hard). Thicker oils and greases tend to stick better in threads. Quote Link to comment Share on other sites More sharing options...
lidl e Posted May 16, 2023 Author Share Posted May 16, 2023 2 hours ago, itu said: Which screws? Machine, wood? For machine screws nearly any oil is better than no oil at all. The only exception is if you need thread lock (nail lacquer for soft, thread lock for hard). Thicker oils and greases tend to stick better in threads. For a bass. Pickguard, bridge and pickups screws Quote Link to comment Share on other sites More sharing options...
gary mac Posted May 17, 2023 Share Posted May 17, 2023 I keep an old candle on my work bench and just pull the screw thread through it. 6 Quote Link to comment Share on other sites More sharing options...
lidl e Posted May 17, 2023 Author Share Posted May 17, 2023 1 hour ago, gary mac said: I keep an old candle on my work bench and just pull the screw thread through it. Beeswax candle or just a regular wax candle? Quote Link to comment Share on other sites More sharing options...
Geek99 Posted May 17, 2023 Share Posted May 17, 2023 I just use red cycle grease 1 Quote Link to comment Share on other sites More sharing options...
PaulThePlug Posted May 17, 2023 Share Posted May 17, 2023 Old Candle or Solid Soap Bar... Make sure ya pilot holes are deep enough, and the correct size - I'm looking at you headstock wiv ya machine heads and rounded head screws... 1 Quote Link to comment Share on other sites More sharing options...
gary mac Posted May 17, 2023 Share Posted May 17, 2023 5 hours ago, lidl e said: Beeswax candle or just a regular wax candle? Just a regular candle. 1 Quote Link to comment Share on other sites More sharing options...
lidl e Posted May 17, 2023 Author Share Posted May 17, 2023 29 minutes ago, gary mac said: Just a regular candle. Nice one. I have one of those. Quote Link to comment Share on other sites More sharing options...
lidl e Posted May 17, 2023 Author Share Posted May 17, 2023 6 hours ago, PaulThePlug said: Old Candle or Solid Soap Bar... Make sure ya pilot holes are deep enough, and the correct size - I'm looking at you headstock wiv ya machine heads and rounded head screws... SO can i ask about pilot holes? SHould they be as deep as the screw is going to go or a little less so? i use a drill bit the same size as the screw without the threads, yeah? I have to do them for pickups, bridge and pickguard so i will be drilling a lot of pilot holes! Quote Link to comment Share on other sites More sharing options...
Reggaebass Posted May 17, 2023 Share Posted May 17, 2023 As some have said, candle wax or a soap bar is ideal for screws, especially into hardwoods, I used to own and work in a joinery shop and every bench had these 1 Quote Link to comment Share on other sites More sharing options...
lidl e Posted May 17, 2023 Author Share Posted May 17, 2023 10 minutes ago, Reggaebass said: As some have said, candle wax or a soap bar is ideal for screws, especially into hardwoods, I used to own and work in a joinery shop and every bench had these Im not sure why i got stuck on the idea it had to be beeswax! 1 Quote Link to comment Share on other sites More sharing options...
Reggaebass Posted May 17, 2023 Share Posted May 17, 2023 4 minutes ago, lidl e said: Im not sure why i got stuck on the idea it had to be beeswax! Beeswax would help but the harder wax is more effective 1 Quote Link to comment Share on other sites More sharing options...
TheGreek Posted May 17, 2023 Share Posted May 17, 2023 Furniture wax. 1 Quote Link to comment Share on other sites More sharing options...
PaulThePlug Posted May 17, 2023 Share Posted May 17, 2023 (edited) Pilot Holes... Hole Deeper than the screw... Say a Machine Head Screw, drill the depth from the screw point, to the underside of the head... when you secure the machine head there will be a fraction of hole left of the machine head thickness... Same for the bridge... just make sure the hole doesn't go all the way through. If the hole isn't deep enough, it will bottom out and you will strip the head. As for hole size... drill should be the size (dia) of the shank of the screw, thats less the threads, to small and it will be too tight, rounding the head it, too big and there will not be enough bite for the threads... this can depend on the hardness of the wood, I recommend a try in a scrap piece of wood. Screwdriver... Cross head screws differ... Pozi, Phillips and JTS. Use a good fitting screwdriver i also use a layer of plastic sandwich bag between screwdriver tip and screw (bolt head to socket...) to protect the finish. Edited May 17, 2023 by PaulThePlug 1 Quote Link to comment Share on other sites More sharing options...
lidl e Posted May 17, 2023 Author Share Posted May 17, 2023 26 minutes ago, PaulThePlug said: Pilot Holes... Hole Deeper than the screw... Say a Machine Head Screw, drill the depth from the screw point, to the underside of the head... when you secure the machine head there will be a fraction of hole left of the machine head thickness... Same for the bridge... just make sure the hole doesn't go all the way through. If the hole isn't deep enough, it will bottom out and you will strip the head. As for hole size... drill should be the size (dia) of the shank of the screw, thats less the threads, to small and it will be too tight, rounding the head it, too big and there will not be enough bite for the threads... this can depend on the hardness of the wood, I recommend a try in a scrap piece of wood. Screwdriver... Cross head screws differ... Pozi, Phillips and JTS. Use a good fitting screwdriver i also use a layer of plastic sandwich bag between screwdriver tip and screw (bolt head to socket...) to protect the finish. Awesome! I'll be going in soon! Quote Link to comment Share on other sites More sharing options...
Cliff Edge Posted May 19, 2023 Share Posted May 19, 2023 Washing up liquid or any liquid soap works. Quote Link to comment Share on other sites More sharing options...
Norris Posted May 21, 2023 Share Posted May 21, 2023 When drilling your pilot holes put a piece of masking tape on the drill bit to mark your depth. Rather than wrapping it tightly just fold it in half to stick to itself. Then it will also clear the swarf from around the hole as it rotates. Keep backing the bit out as you drill - you want to keep the grooves clear for a nice clean hole. Yes, drill bit the size of the screw shank excluding the thread, and a bit of normal candle wax. Also make sure you use a screwdriver that fits the screw head properly. Some of those screws seem to be made out of cheese and mash/shear easily (I'm looking at your machine head screws Kluson!) 1 Quote Link to comment Share on other sites More sharing options...
lidl e Posted May 21, 2023 Author Share Posted May 21, 2023 Got 'em 1 Quote Link to comment Share on other sites More sharing options...
PaulThePlug Posted May 21, 2023 Share Posted May 21, 2023 On 19/05/2023 at 17:37, Cliff Edge said: Washing up liquid or any liquid soap works. I'd be wary as its wet... and stay's wet. I'd go with dry soap bar or candle wax 1 Quote Link to comment Share on other sites More sharing options...
Reggaebass Posted May 21, 2023 Share Posted May 21, 2023 Wet lubricant can also soak into the wood and stain it, that’s why the harder ones are better 1 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.