What single thing would you like a gear company to do that they don't do currently?

[fretmeister]

  On 07/09/2023 at 21:01, LowB_FTW said:

Sandberg to do a Forty Eight bass, 5-String with reverse in-line headstock.

 

Mark

Expand  

 

@LowB_FTW

 

You can custom order that.

[Len_derby]

I'd like gear manufacturers to give preferential deals to bricks-and-mortar retailers so that it became cheaper to buy from a shop than order on-line.

[fretmeister]

  On 11/09/2023 at 12:27, Len_derby said:

I'd like gear manufacturers to give preferential deals to bricks-and-mortar retailers so that it became cheaper to buy from a shop than order on-line.

Expand  

 

 

Aren't a huge amount of online places also bricks and mortar shops?

[fretmeister]

I'd like @Tech21NYC to do a smaller version of the Steve Harris pedal. A Boss sized enclosure with a single channel, no tuner. That would be much better for pedal board use. I only sold mine  because it's just inconvenient for a Pedaltrain type set up. It's such a great pedal, even if just used as an overdrive. (Ideally stick a compressor in the existing one too).

 

And while you are at it - do a V3 of the Paradriver with the Presence control from the BDDI V2... and stick the jack sockets and power input on the top edge to help with 'board space a bit.

 

 

[asingardenof]

Fender to spend five years without releasing a new variation on a Jazz or Precision bass to give them some time to come up with some new ideas.

[Leonard Smalls]

  On 09/09/2023 at 12:04, Hellzero said:

GR Bass AeroTech Full Carbon Combo 800 (Watts at 4 Ohms)

Expand  

Pah!

My Crown class D power amp is 1500W rms bridged into 4 ohms 😁 And weighs around 4 kgs...

Do we have a large trousers emoji? 🐎😄

[fretmeister]

I have hassled him before  but I'd like Barefaced @alexclaber to do a vertical Three10T cab with kickback wheels, and a tweeter.

 

Alex has kindly informed me that to get a sensible 4ohm impedance it would need custom ordered cones and that the demand probably wouldn't be there for the expense and R&D. So I'm counting on you lot to tell him that you'd all buy 3 cabs each!    

 

Narrow and tall, with wheels would be perfect for me. The Four10 doesn't have wheels and is short, the Six10 is just completely overdoing it and there are many venues I play I'd have trouble getting it through doors / stairs etc and with about 20 band members there isn't much room either. The Eight10 gives me funny feelings in my loins but it wouldn't fit in the car.

 

My feeble attempts at saying "Well, Ashdown have made one..." didn't work in the slightest, but it was worth a shot. So I'm going to try "More people will want to have sex with you, Alex, if you make it"*

 

 

 

 

* Those people are likely to just be Basschat members or maybe even me, but that's your risk!

[TimR]

  On 11/09/2023 at 12:46, fretmeister said:

I have hassled him before  but I'd like Barefaced @alexclaber to do a vertical Three10T cab with kickback wheels, and a tweeter.

 

Alex has kindly informed me that to get a sensible 4ohm impedance it would need custom ordered cones and that the demand probably wouldn't be there for the expense and R&D. So I'm counting on you lot to tell him that you'd all buy 3 cabs each!    

 

Narrow and tall, with wheels would be perfect for me. The Four10 doesn't have wheels and is short, the Six10 is just completely overdoing it and there are many venues I play I'd have trouble getting it through doors / stairs etc and with about 20 band members there isn't much room either. The Eight10 gives me funny feelings in my loins but it wouldn't fit in the car.

 

My feeble attempts at saying "Well, Ashdown have made one..." didn't work in the slightest, but it was worth a shot. So I'm going to try "More people will want to have sex with you, Alex, if you make it"*

 

 

 

 

* Those people are likely to just be Basschat members or maybe even me, but that's your risk!

Expand  

 

There's always the 2x12". A 3x10" would only have 4% more cone area and possibly that would be lost due to less excursion on the 10s so don't really see the advantage. 

[fretmeister]

  On 11/09/2023 at 14:25, TimR said:

 

There's always the 2x12". A 3x10" would only have 4% more cone area and possibly that would be lost due to less excursion on the 10s so don't really see the advantage. 

Expand  

 

I had one. It was nice, but I like the sound of their 10 inch cones more. 

[Passinwind]

  On 08/09/2023 at 09:03, Downunderwonder said:

You entirely missed the point.

 

Most of us know what gain is by definition. We also use the term the wrong way so you'll have to get over it.

 

Gain as in "moar rawk" without an increase in volume, was the request.

 

 

Expand  

Then just call it what it is: distortion. 😉

[Russ]

  On 11/09/2023 at 12:46, fretmeister said:

I have hassled him before  but I'd like Barefaced @alexclaber to do a vertical Three10T cab with kickback wheels, and a tweeter.

 

Alex has kindly informed me that to get a sensible 4ohm impedance it would need custom ordered cones and that the demand probably wouldn't be there for the expense and R&D. So I'm counting on you lot to tell him that you'd all buy 3 cabs each!    

 

Narrow and tall, with wheels would be perfect for me. The Four10 doesn't have wheels and is short, the Six10 is just completely overdoing it and there are many venues I play I'd have trouble getting it through doors / stairs etc and with about 20 band members there isn't much room either. The Eight10 gives me funny feelings in my loins but it wouldn't fit in the car.

 

My feeble attempts at saying "Well, Ashdown have made one..." didn't work in the slightest, but it was worth a shot. So I'm going to try "More people will want to have sex with you, Alex, if you make it"*

 

 

 

 

* Those people are likely to just be Basschat members or maybe even me, but that's your risk!

Expand  

It could be done as a 5.33 ohm cab (3x16 ohm speakers in parallel). Most amps will handle that. Markbass and Ashdown have both done 3x10" cabs and done pretty well with them. 

 

I'd buy one.

[Woodinblack]

  On 11/09/2023 at 12:40, asingardenof said:

Fender to spend five years without releasing a new variation on a Jazz or Precision bass to give them some time to come up with some new ideas.

Expand  

 

They tried - for all that people moan about it, noone will buy it

[Jean-Luc Pickguard]

  On 11/09/2023 at 15:36, Woodinblack said:

 

They tried - for all that people moan about it, noone will buy it

Expand  

[LowB_FTW]

  On 11/09/2023 at 12:25, fretmeister said:

 

@LowB_FTW

 

You can custom order that.

Expand  

Possibly. I wasn't aware that Sandberg did 5 in-line headstocks though.

 

Mark

[Downunderwonder]

  On 11/09/2023 at 14:45, Passinwind said:

Then just call it what it is: distortion. 😉

Expand  

It doesn't matter what anyone calls it when it's adding gain and causing soundguy's head to explode.

[Bolo]

  On 11/09/2023 at 18:14, Downunderwonder said:

It doesn't matter what anyone calls it when it's adding gain and causing soundguy's head to explode.

Expand  

Drive is not Gain. Just like Gain is not Volume. The names are different because the operation is different.

 

[fretmeister]

  On 11/09/2023 at 18:19, Bolo said:

Drive is not Gain. Just like Gain is not Volume. The names are different because the operation is different.

 

Expand  

 

After 50+ years of pedal makers using it wrong... there's no point trying to fight this one.

[TimR]

When the Sansamp technical guy comes on and clarifies it and then everyone ignores them...

 

Read the thread chaps...

 

😆

[Downunderwonder]

  On 11/09/2023 at 18:19, Bolo said:

Drive is not Gain. Just like Gain is not Volume. The names are different because the operation is different.

 

Expand  

Still ignores the request for a solution to a practical problem.

[TimR]

  On 11/09/2023 at 21:43, Downunderwonder said:

Still ignores the request for a solution to a practical problem.

Expand  

If you read the reply from the Sansamp tech you asked for:

 

It's not a 'problem'. It's how all gain structures work and and amplifier stages work. 

 

The problem is the user understanding it. 

 

If I have a PA. It has gain and volume. How you adjust gain and volume is up to the end user. Both affect the final volume. 

 

"Drive" is different as it's intention is to drive the input stage into clipping. So as you increase it the volume increases until it starts to clip. At which point the volume doesn't increase anymore, you just get more distortion (and compression).

 

The "drive" on the other pedal is in a separate module with blend control. So doesn't affect the overall volume. 

 

It's just a case of understanding how it's designed to work and what the terms mean.

 

A gain of 1 or 0dB is unity. Have a look at the controls on your PA. Note the 0dB level marks. 

Edited September 11, 2023 by TimR

[Norris]

Squier or Fender to make an affordable 5-string precision 

 

Ah, too late, I bought a Sire (and love it)

[Downunderwonder]

  On 11/09/2023 at 22:16, TimR said:

If you read the reply from the Sansamp tech you asked for:

 

It's not a 'problem'. It's how all gain structures work and and amplifier stages work. 

 

The problem is the user understanding it. 

 

If I have a PA. It has gain and volume. How you adjust gain and volume is up to the end user. Both affect the final volume. 

 

"Drive" is different as it's intention is to drive the input stage into clipping. So as you increase it the volume increases until it starts to clip. At which point the volume doesn't increase anymore, you just get more distortion (and compression).

 

The "drive" on the other pedal is in a separate module with blend control. So doesn't affect the overall volume. 

 

It's just a case of understanding how it's designed to work and what the terms mean.

 

A gain of 1 or 0dB is unity. Have a look at the controls on your PA. Note the 0dB level marks. 

Expand  

Deaf ears.

[tauzero]

Line 6 to make another Variax bass using the current HD technology. And preferably make it headless. Perhaps marketing it as a bass that can make a huge variety of sounds, and making it Workbench compatible, rather than saying it's exact emulations of various basses.

[Huge Hands]

Would like Fender to design and release a 5-string version of the '51 slab P that looks kind of normal but still has normal string spacing and comes in various colours, not just butterscotch and Sting - and not be a very expensive one-off custom thing.

 

...then pass the designs on to Squier so I have a chance of affording one.   And then maybe Sire will do a sorted version and I can just about afford that.....

[fretmeister]

  On 11/09/2023 at 22:16, TimR said:

If you read the reply from the Sansamp tech you asked for:

 

It's not a 'problem'. It's how all gain structures work and and amplifier stages work. 

 

The problem is the user understanding it. 

 

If I have a PA. It has gain and volume. How you adjust gain and volume is up to the end user. Both affect the final volume. 

 

"Drive" is different as it's intention is to drive the input stage into clipping. So as you increase it the volume increases until it starts to clip. At which point the volume doesn't increase anymore, you just get more distortion (and compression).

 

The "drive" on the other pedal is in a separate module with blend control. So doesn't affect the overall volume. 

 

It's just a case of understanding how it's designed to work and what the terms mean.

 

A gain of 1 or 0dB is unity. Have a look at the controls on your PA. Note the 0dB level marks. 

Expand  

 

 

I think he knows exactly how it works - What he wants is a unit where increasing the gain automatically lowers the volume to keep a consistent overall output.

 

Some compressors do this already, when the ratio is increased or the threshold is lowered the make up gain is dealt with automatically to keep the output consistent. It shouldn't be that hard to do on a drive pedal / preamp unit.